[pipsolar] Type the switch table so pylint sees the setter as callable

Co-authored-by: J. Nick Koston <nick@koston.org>
Co-authored-by: J. Nick Koston <nick@home-assistant.io>

esphome/components/dlms_meter/__init__.py

@@ -22,7 +22,7 @@ CONF_CUSTOM_PATTERNS = "custom_patterns"
 CONF_SKIP_CRC = "skip_crc"
 CONF_DEFAULT_OBIS = "default_obis"
 
-DLMS_PARSER_VERSION = "2.2.0"
+DLMS_PARSER_VERSION = "2.2.2"
 
 dlms_meter_component_ns = cg.esphome_ns.namespace("dlms_meter")
 DlmsMeterComponent = dlms_meter_component_ns.class_(

esphome/components/esp32/__init__.py

@@ -2389,7 +2389,9 @@ FRAMEWORK_SCHEMA = cv.Schema(
                     cv.Schema(
                         {
                             cv.Required(CONF_NAME): cv.string_strict,
-                            cv.Optional(CONF_SOURCE): cv.git_ref,
+                            cv.Optional(CONF_SOURCE): cv.All(
+                                cv.string_strict, cv.Length(min=1)
+                            ),
                             cv.Optional(CONF_REF): cv.string,
                             cv.Optional(CONF_PATH): cv.string,
                         }

esphome/components/ld2420/ld2420.cpp

@@ -138,6 +138,11 @@ static uint8_t calc_checksum(const void *data, size_t size) {
   return xor_bytes(static_cast<const uint8_t *>(data), size);
 }
 
+// Simple mode needs simple reporting from the module; Normal and Calibrate read energy frames
+static uint16_t system_mode_for(uint8_t mode) {
+  return mode == OP_SIMPLE_MODE ? CMD_SYSTEM_MODE_SIMPLE : CMD_SYSTEM_MODE_ENERGY;
+}
+
 static int32_t get_firmware_int(const char *version_string) {
   // Convert "v1.5.4" -> 154 by skipping 'v' and '.', accumulating digits
   const char *p = (*version_string == 'v') ? version_string + 1 : version_string;
@@ -207,13 +212,10 @@ void LD2420Component::setup() {
 
   memcpy(&this->new_config, &this->current_config, sizeof(this->current_config));
   if (ld2420::get_firmware_int(this->firmware_ver_) < CALIBRATE_VERSION_MIN) {
-    this->set_operating_mode(OP_SIMPLE_MODE);
-    this->set_mode_(CMD_SYSTEM_MODE_SIMPLE);
     ESP_LOGW(TAG, "Firmware version %s and older supports Simple Mode only", this->firmware_ver_);
-  } else {
-    this->set_operating_mode(OP_NORMAL_MODE);
-    this->set_mode_(CMD_SYSTEM_MODE_ENERGY);
   }
+  this->set_operating_mode(OP_NORMAL_MODE);  // older firmware is held in Simple
+  this->set_mode_(system_mode_for(this->current_operating_mode));
 #ifdef USE_NUMBER
   this->init_gate_config_numbers();
 #endif
@@ -244,7 +246,9 @@ void LD2420Component::apply_config_action() {
 #endif
   this->set_system_mode(this->system_mode_);
   this->set_config_mode(false);  // Disable config mode to save new values in LD2420 nvm
-  this->set_operating_mode(OP_NORMAL_MODE);
+  // Applying the calibrated thresholds ends calibration; Normal and Simple stay as they are
+  if (this->current_operating_mode == OP_CALIBRATE_MODE)
+    this->set_operating_mode(OP_NORMAL_MODE);
 }
 
 void LD2420Component::factory_reset_action() {
@@ -356,6 +360,22 @@ void LD2420Component::set_operating_mode(const char *state) {
   }
 }
 
+void LD2420Component::change_operating_mode(OpMode mode) {
+  this->set_operating_mode(mode);
+  const uint16_t system_mode = system_mode_for(this->current_operating_mode);
+  if (system_mode == this->get_mode_())
+    return;
+  if (this->set_config_mode(true) != LD2420_ERROR_TIMEOUT) {
+    this->set_system_mode(system_mode);
+    this->set_config_mode(false);
+  }
+  if (this->get_mode_() != system_mode) {
+    // The module kept its reporting mode; show the mode that matches it
+    ESP_LOGE(TAG, ESP_LOG_MSG_COMM_FAIL);
+    this->set_operating_mode(this->get_mode_() == CMD_SYSTEM_MODE_SIMPLE ? OP_SIMPLE_MODE : OP_NORMAL_MODE);
+  }
+}
+
 void LD2420Component::set_operating_mode(OpMode mode) {
   // Older firmware only supports simple mode
   if (ld2420::get_firmware_int(this->firmware_ver_) < CALIBRATE_VERSION_MIN) {

esphome/components/ld2420/ld2420.h

@@ -119,6 +119,7 @@ class LD2420Component final : public Component, public uart::UARTDevice {
   void handle_cmd_error(uint16_t error);
   void set_operating_mode(const char *state);
   void set_operating_mode(OpMode mode);
+  void change_operating_mode(OpMode mode);
   void auto_calibrate_sensitivity();
   void update_radar_data(uint16_t const *gate_energy, uint8_t sample_number);
   uint8_t set_config_mode(bool enable);

esphome/components/ld2420/select/__init__.py

@@ -30,6 +30,5 @@ async def to_code(config: ConfigType) -> None:
         CONF_OPERATING_MODE,
         hub.set_operating_mode_select,
         options=CONF_SELECTS,
-        apply="set_operating_mode(static_cast<ld2420::OpMode>(index + 1))",
-        publish="before",
+        apply="change_operating_mode(static_cast<ld2420::OpMode>(index + 1))",
     )

esphome/components/logger/__init__.py

@@ -607,9 +607,10 @@ async def _late_logger_init(config: ConfigType) -> None:
         # esp_rom_printf instead of pulling ~1.2KB esp_rom_vprintf into IRAM.
         # S2/C2 have a ROM vprintf, so IDF forces CONSTRAINED_ENV_SAFE=1 and
         # cache-off DRAM logs would reach the flash-resident wrapper; keep V1.
-        if idf_version() >= cv.Version(6, 1, 0) and get_esp32_variant() not in (
-            VARIANT_ESP32C2,
-            VARIANT_ESP32S2,
+        if (
+            CORE.using_toolchain_esp_idf
+            and idf_version() >= cv.Version(6, 1, 0)
+            and get_esp32_variant() not in (VARIANT_ESP32C2, VARIANT_ESP32S2)
         ):
             add_idf_sdkconfig_option("CONFIG_LOG_VERSION_1", False)
             add_idf_sdkconfig_option("CONFIG_LOG_VERSION_2", True)

esphome/components/microphone/microphone.h

@@ -4,6 +4,7 @@
 
 #include <cstddef>
 #include <cstdint>
+#include <cstring>
 #include <span>
 #include <type_traits>
 #include <utility>
@@ -53,16 +54,25 @@ using DataCallbackManagerBase = CallbackManager<void(const AudioCapture &)>;
 
 class DataCallbackManager : public DataCallbackManagerBase {
  public:
-  explicit DataCallbackManager(const audio::AudioStreamInfo *stream_info) : stream_info_(stream_info) {}
+  DataCallbackManager(const audio::AudioStreamInfo *stream_info, const bool *mute_state)
+      : stream_info_(stream_info), mute_state_(mute_state) {}
 
   using DataCallbackManagerBase::call;
 
   // Remove before 2027.5.0, along with this class (use a plain CallbackManager)
   ESPDEPRECATED("Use Microphone::publish_audio_() instead. Removed in 2027.5.0", "2026.11.0")
-  void call(const std::vector<uint8_t> &data) { this->call(AudioCapture{data, *this->stream_info_, 0}); }
+  void call(const std::vector<uint8_t> &data) {
+    if (*this->mute_state_) {
+      const std::vector<uint8_t> zeros(data.size(), 0);
+      this->call(AudioCapture{zeros, *this->stream_info_, 0});
+    } else {
+      this->call(AudioCapture{data, *this->stream_info_, 0});
+    }
+  }
 
  protected:
   const audio::AudioStreamInfo *stream_info_;
+  const bool *mute_state_;
 };
 
 class Microphone {
@@ -72,15 +82,7 @@ class Microphone {
 
   /// Callbacks take (const AudioCapture &) and run on the microphone's task.
   template<typename F> void add_data_callback(F &&data_callback) {
-    this->data_callbacks_.add(
-        [this, callback = as_capture_callback(std::forward<F>(data_callback))](const AudioCapture &capture) {
-          if (this->mute_state_) {
-            const std::vector<uint8_t> zeros(capture.data.size(), 0);
-            callback(AudioCapture{zeros, capture.stream_info, capture.capture_time_us});
-          } else {
-            callback(capture);
-          }
-        });
+    this->data_callbacks_.add(as_capture_callback(std::forward<F>(data_callback)));
   }
 
   bool is_running() const { return this->state_ == STATE_RUNNING; }
@@ -92,8 +94,11 @@ class Microphone {
   audio::AudioStreamInfo get_audio_stream_info() { return this->audio_stream_info_; }
 
  protected:
-  void publish_audio_(std::span<const uint8_t> data, const audio::AudioStreamInfo &stream_info,
-                      int64_t capture_time_us = 0) {
+  /// While muted, data is zeroed first, so it must be a buffer the platform owns.
+  void publish_audio_(std::span<uint8_t> data, const audio::AudioStreamInfo &stream_info, int64_t capture_time_us = 0) {
+    if (this->mute_state_) {
+      std::memset(data.data(), 0, data.size());
+    }
     this->data_callbacks_.call(AudioCapture{data, stream_info, capture_time_us});
   }
 
@@ -105,7 +110,7 @@ class Microphone {
   audio::AudioStreamInfo audio_stream_info_;
 
   // Make private when the deprecated call(data) is removed in 2027.5.0
-  DataCallbackManager data_callbacks_{&this->audio_stream_info_};
+  DataCallbackManager data_callbacks_{&this->audio_stream_info_, &this->mute_state_};
 };
 
 }  // namespace esphome::microphone

esphome/components/pipsolar/output/pipsolar_output.cpp

@@ -12,7 +12,7 @@ void PipsolarOutput::write_state(float state) {
 
   if (std::find(this->possible_values_.begin(), this->possible_values_.end(), state) != this->possible_values_.end()) {
     ESP_LOGD(TAG, "Will write: %s out of value %f / %02.0f", tmp, state, state);
-    this->parent_->queue_command(std::string(tmp));
+    this->parent_->queue_command(tmp);
   } else {
     ESP_LOGD(TAG, "Will not write: %s as it is not in list of allowed values", tmp);
   }

esphome/components/pipsolar/pipsolar.cpp

@@ -224,17 +224,23 @@ bool Pipsolar::send_next_poll_() {
   return false;
 }
 
-void Pipsolar::queue_command(const std::string &command) {
+void Pipsolar::write_switch(bool state, const char *on, const char *off) {
+  const char *command = state ? on : off;
+  if (command != nullptr)
+    this->queue_command(command);
+}
+
+void Pipsolar::queue_command(const char *command) {
   uint8_t next_position = command_queue_position_;
   for (uint8_t i = 0; i < COMMAND_QUEUE_LENGTH; i++) {
     uint8_t testposition = (next_position + i) % COMMAND_QUEUE_LENGTH;
     if (command_queue_[testposition].empty()) {
       command_queue_[testposition] = command;
-      ESP_LOGD(TAG, "Command queued successfully: %s at position %d", command.c_str(), testposition);
+      ESP_LOGD(TAG, "Command queued successfully: %s at position %d", command, testposition);
       return;
     }
   }
-  ESP_LOGD(TAG, "Command queue full dropping command: %s", command.c_str());
+  ESP_LOGD(TAG, "Command queue full dropping command: %s", command);
 }
 
 void Pipsolar::handle_poll_response_(ENUMPollingCommand polling_command, const char *message) {

esphome/components/pipsolar/pipsolar.h

@@ -194,7 +194,10 @@ class Pipsolar final : public uart::UARTDevice, public PollingComponent {
   PIPSOLAR_SWITCH(pv_ok_condition_for_parallel_switch, QPIRI)
   PIPSOLAR_SWITCH(pv_power_balance_switch, QPIRI)
 
-  void queue_command(const std::string &command);
+  void queue_command(const char *command);
+  void queue_command(const std::string &command) { this->queue_command(command.c_str()); }
+  // A switch write; off is nullptr when the inverter has no off command
+  void write_switch(bool state, const char *on, const char *off);
   void setup() override;
   void loop() override;
   void dump_config() override;

esphome/components/pipsolar/switch/__init__.py

@@ -1,10 +1,14 @@
+from collections.abc import Callable
+from typing import NamedTuple
+
 import esphome.codegen as cg
 from esphome.components import switch
 import esphome.config_validation as cv
 from esphome.const import ICON_POWER
+from esphome.cpp_generator import MockObj
 from esphome.types import ConfigType
 
-from .. import CONF_PIPSOLAR_ID, PIPSOLAR_COMPONENT_SCHEMA, pipsolar_ns
+from .. import CONF_PIPSOLAR_ID, PIPSOLAR_COMPONENT_SCHEMA
 
 DEPENDENCIES = ["uart"]
 
@@ -16,21 +20,55 @@ CONF_INPUT_VOLTAGE_RANGE = "input_voltage_range"
 CONF_PV_OK_CONDITION_FOR_PARALLEL = "pv_ok_condition_for_parallel"
 CONF_PV_POWER_BALANCE = "pv_power_balance"
 
+
+class _PipSwitch(NamedTuple):
+    setter: Callable[[MockObj], MockObj]
+    on: str
+    off: str | None  # None when the inverter has no off command
+
+
+# Each switch's hub setter and its on and off commands
 TYPES = {
-    CONF_OUTPUT_SOURCE_PRIORITY_UTILITY: ("POP00", None),
-    CONF_OUTPUT_SOURCE_PRIORITY_SOLAR: ("POP01", None),
-    CONF_OUTPUT_SOURCE_PRIORITY_BATTERY: ("POP02", None),
-    CONF_OUTPUT_SOURCE_PRIORITY_HYBRID: ("POP03", None),
-    CONF_INPUT_VOLTAGE_RANGE: ("PGR01", "PGR00"),
-    CONF_PV_OK_CONDITION_FOR_PARALLEL: ("PPVOKC1", "PPVOKC0"),
-    CONF_PV_POWER_BALANCE: ("PSPB1", "PSPB0"),
+    CONF_OUTPUT_SOURCE_PRIORITY_UTILITY: _PipSwitch(
+        lambda hub: hub.set_output_source_priority_utility_switch,
+        "POP00",
+        None,
+    ),
+    CONF_OUTPUT_SOURCE_PRIORITY_SOLAR: _PipSwitch(
+        lambda hub: hub.set_output_source_priority_solar_switch,
+        "POP01",
+        None,
+    ),
+    CONF_OUTPUT_SOURCE_PRIORITY_BATTERY: _PipSwitch(
+        lambda hub: hub.set_output_source_priority_battery_switch,
+        "POP02",
+        None,
+    ),
+    CONF_OUTPUT_SOURCE_PRIORITY_HYBRID: _PipSwitch(
+        lambda hub: hub.set_output_source_priority_hybrid_switch,
+        "POP03",
+        None,
+    ),
+    CONF_INPUT_VOLTAGE_RANGE: _PipSwitch(
+        lambda hub: hub.set_input_voltage_range_switch,
+        "PGR01",
+        "PGR00",
+    ),
+    CONF_PV_OK_CONDITION_FOR_PARALLEL: _PipSwitch(
+        lambda hub: hub.set_pv_ok_condition_for_parallel_switch,
+        "PPVOKC1",
+        "PPVOKC0",
+    ),
+    CONF_PV_POWER_BALANCE: _PipSwitch(
+        lambda hub: hub.set_pv_power_balance_switch,
+        "PSPB1",
+        "PSPB0",
+    ),
 }
 
-PipsolarSwitch = pipsolar_ns.class_("PipsolarSwitch", switch.Switch, cg.Component)
-
 PIPSWITCH_SCHEMA = switch.switch_schema(
-    PipsolarSwitch, icon=ICON_POWER, block_inverted=True
-).extend(cv.COMPONENT_SCHEMA)
+    switch.ApplySwitch, icon=ICON_POWER, block_inverted=True
+)
 
 CONFIG_SCHEMA = PIPSOLAR_COMPONENT_SCHEMA.extend(
     {cv.Optional(type): PIPSWITCH_SCHEMA for type in TYPES}
@@ -38,15 +76,11 @@ CONFIG_SCHEMA = PIPSOLAR_COMPONENT_SCHEMA.extend(
 
 
 async def to_code(config: ConfigType) -> None:
-    paren = await cg.get_variable(config[CONF_PIPSOLAR_ID])
-
-    for type, (on, off) in TYPES.items():
-        if type in config:
-            conf = config[type]
-            var = await switch.new_switch(conf)
-            await cg.register_component(var, conf)
-            cg.add(getattr(paren, f"set_{type}_switch")(var))
-            cg.add(var.set_parent(paren))
-            cg.add(var.set_on_command(on))
-            if off is not None:
-                cg.add(var.set_off_command(off))
+    hub = await cg.get_variable(config[CONF_PIPSOLAR_ID])
+    switches = switch.sub_switches(config, parent=hub)
+    # The hub polls the inverter and publishes each switch's state
+    for key, sw in TYPES.items():
+        off_arg = "nullptr" if sw.off is None else f'"{sw.off}"'
+        await switches(
+            key, sw.setter(hub), apply=f'write_switch(state, "{sw.on}", {off_arg})'
+        )

esphome/components/pipsolar/switch/pipsolar_switch.cpp

@@ -1,17 +0,0 @@
-#include "pipsolar_switch.h"
-#include "esphome/core/log.h"
-#include "esphome/core/application.h"
-
-namespace esphome::pipsolar {
-
-ESPHOME_LOG_TAG(TAG, "pipsolar.switch");
-
-void PipsolarSwitch::dump_config() { LOG_SWITCH("", "Pipsolar Switch", this); }
-void PipsolarSwitch::write_state(bool state) {
-  const char *command = state ? this->on_command_ : this->off_command_;
-  if (command != nullptr) {
-    this->parent_->queue_command(command);
-  }
-}
-
-}  // namespace esphome::pipsolar

esphome/components/pipsolar/switch/pipsolar_switch.h

@@ -1,26 +0,0 @@
-#pragma once
-
-#include "../pipsolar.h"
-#include "esphome/components/switch/switch.h"
-#include "esphome/core/component.h"
-
-namespace esphome::pipsolar {
-class Pipsolar;
-class PipsolarSwitch final : public switch_::Switch, public Component {
- public:
-  void set_parent(Pipsolar *parent) { this->parent_ = parent; }
-  void set_on_command(const char *command) { this->on_command_ = command; }
-  void set_off_command(const char *command) { this->off_command_ = command; }
-  /// Prevent accidental use of std::string which would dangle
-  void set_on_command(const std::string &command) = delete;
-  void set_off_command(const std::string &command) = delete;
-  void dump_config() override;
-
- protected:
-  void write_state(bool state) override;
-  const char *on_command_{nullptr};
-  const char *off_command_{nullptr};
-  Pipsolar *parent_;
-};
-
-}  // namespace esphome::pipsolar

esphome/components/resampler/microphone/resampler_microphone.cpp

@@ -90,6 +90,7 @@ bool ResamplerMicrophone::init_resampler_(const audio::AudioStreamInfo &input_st
 
   if (input_stream_info.get_sample_rate() == this->target_sample_rate_) {
     // The source already delivers the target sample rate, so its audio is passed through unchanged
+    this->output_buffer_.reserve(input_stream_info.ms_to_bytes(BUFFER_DURATION_MS));
     this->input_stream_info_ = input_stream_info;
     this->resampler_ready_ = true;
     return true;
@@ -137,7 +138,23 @@ void ResamplerMicrophone::process_audio_(const microphone::AudioCapture &capture
   }
 
   if (this->resampler_ == nullptr) {
-    this->publish_audio_(capture.data, input_stream_info, capture.capture_time_us);
+    if (this->mute_state_) {
+      // The source's buffer is shared with its other consumers, so publish zeros from our own buffer, in pieces that
+      // fit its reserved size so muting never allocates
+      const uint32_t max_frames = input_stream_info.ms_to_frames(BUFFER_DURATION_MS);
+      const uint32_t total_frames = input_stream_info.bytes_to_frames(capture.data.size());
+      for (uint32_t done = 0; done < total_frames;) {
+        const uint32_t frames = std::min(total_frames - done, max_frames);
+        this->output_buffer_.assign(input_stream_info.frames_to_bytes(frames), 0);
+        const int64_t time_us =
+            capture.capture_time_us == 0 ? 0 : capture.capture_time_us + input_stream_info.frames_to_microseconds(done);
+        this->publish_audio_(this->output_buffer_, input_stream_info, time_us);
+        done += frames;
+      }
+    } else {
+      // Needs a protected forwarding method once data_callbacks_ is made private in 2027.5.0
+      this->data_callbacks_.call(microphone::AudioCapture{capture.data, input_stream_info, capture.capture_time_us});
+    }
     return;
   }
 

esphome/components/tas58xx/audio_dac.py

@@ -6,6 +6,7 @@ from esphome.automation import maybe_simple_id
 import esphome.codegen as cg
 from esphome.components import i2c
 from esphome.components.audio_dac import AudioDac
+from esphome.components.const import CONF_MODULATION
 import esphome.config_validation as cv
 from esphome.const import CONF_ENABLE_PIN, CONF_ID, CONF_MODEL
 from esphome.cpp_generator import MockObj
@@ -19,6 +20,7 @@ DEPENDENCIES = ["i2c"]
 
 CONF_ANALOG_GAIN = "analog_gain"
 CONF_DAC_MODE = "dac_mode"
+CONF_FAULT_OUTPUT = "fault_output"
 CONF_IGNORE_ENABLE_PIN_WARNING = "ignore_enable_pin_warning"
 CONF_MIXER_MODE = "mixer_mode"
 CONF_VOLUME_MIN_DB = "volume_min_db"
@@ -39,6 +41,11 @@ MIXER_MODES = MixerMode.options(
     "stereo", "stereo_inverse", "mono", "left", "right", prefix="MIXER_MODE_"
 )
 
+Modulation = tas58xx_ns.enum("Modulation")
+MODULATIONS = Modulation.options("bd_mode", "1spw_mode", prefix="MODULATION_")
+
+FAULT_OUTPUT_NONE = "none"
+
 
 @dataclass(frozen=True)
 class Model:
@@ -49,6 +56,9 @@ class Model:
     volume_min_db: float
     volume_max_db: float
     default_address: int
+    # Pins that can report FAULTZ: name -> pin number n, selected at 0x61 + n (ModelInfo::fault_output_pins)
+    fault_outputs: dict[str, int]
+    default_fault_output: str
 
 
 MODELS: dict[str, Model] = {
@@ -58,6 +68,8 @@ MODELS: dict[str, Model] = {
         volume_min_db=-103.0,
         volume_max_db=24.0,
         default_address=0x2D,
+        fault_outputs={"adr": 0},
+        default_fault_output="adr",
     ),
     DAC_TAS5825M: Model(
         model_info=tas58xx_ns.TAS5825M_MODEL,
@@ -65,6 +77,8 @@ MODELS: dict[str, Model] = {
         volume_min_db=-103.0,
         volume_max_db=24.0,
         default_address=0x4C,
+        fault_outputs={"gpio0": 0, "gpio1": 1, "gpio2": 2},
+        default_fault_output="gpio1",
     ),
 }
 
@@ -100,9 +114,15 @@ def _model_schema(model: Model) -> cv.Schema:
                 cv.Optional(CONF_DAC_MODE, default="btl"): cv.enum(
                     DAC_MODES, lower=True
                 ),
+                cv.Optional(
+                    CONF_FAULT_OUTPUT, default=model.default_fault_output
+                ): cv.one_of(FAULT_OUTPUT_NONE, *model.fault_outputs, lower=True),
                 cv.Optional(CONF_MIXER_MODE, default="stereo"): cv.enum(
                     MIXER_MODES, lower=True
                 ),
+                cv.Optional(CONF_MODULATION, default="bd_mode"): cv.enum(
+                    MODULATIONS, lower=True
+                ),
                 cv.Optional(
                     CONF_VOLUME_MIN_DB, default=model.volume_min_db
                 ): volume_validator,
@@ -172,7 +192,10 @@ async def to_code(config: ConfigType) -> None:
 
     cg.add(var.set_analog_gain(config[CONF_ANALOG_GAIN]))
     cg.add(var.set_dac_mode(config[CONF_DAC_MODE]))
+    if (fault_output := config[CONF_FAULT_OUTPUT]) != FAULT_OUTPUT_NONE:
+        cg.add(var.set_fault_output(model.fault_outputs[fault_output]))
     cg.add(var.set_mixer_mode(config[CONF_MIXER_MODE]))
+    cg.add(var.set_modulation(config[CONF_MODULATION]))
     cg.add(var.set_volume_min_db(config[CONF_VOLUME_MIN_DB]))
     cg.add(var.set_volume_max_db(config[CONF_VOLUME_MAX_DB]))
     await cg.add_pin(var.set_enable_pin, config.get(CONF_ENABLE_PIN))

esphome/components/tas58xx/model_tas5805m.cpp

@@ -8,11 +8,8 @@ namespace esphome::tas58xx {
 // Registers 0x46, 0x7D, 0x7E and page 1 register 0x51 are not documented in the datasheet.
 static constexpr i2c::I2CRegValue STARTUP_SEQUENCE[] PROGMEM = {
     {0x03, 0x00},  // DEVICE_CTRL_2: deep sleep
-    {0x46, 0x01},
+    {0x46, 0x01},  // PPC 96 kHz process flow value (its 48 kHz FIR flows write 0x11)
     {0x03, 0x02},  // DEVICE_CTRL_2: Hi-Z
-    // The I2C address is latched at power up, after which the ADR pin can report faults
-    {0x61, 0x0B},  // ADR_PIN_CONFIG: FAULTZ
-    {0x60, 0x01},  // ADR_PIN_CTRL: output
     {0x7D, 0x11},
     {0x7E, 0xFF},
     {0x00, 0x01},  // Page 1
@@ -25,6 +22,8 @@ static constexpr i2c::I2CRegValue STARTUP_SEQUENCE[] PROGMEM = {
 
 static const LogString *model_name() { return LOG_STR("TAS5805M"); }
 
+static const LogString *fault_output_name(uint8_t) { return LOG_STR("ADR"); }
+
 // An if chain rather than a switch: a switch table would land in rodata, which is RAM on ESP8266.
 static const LogString *fault_name(uint8_t index) {
   if (index == 0)
@@ -88,6 +87,8 @@ const ModelInfo TAS5805M_MODEL = {
             NO_BIT,  // FAULT_SENSOR_RIGHT_CHANNEL_CBC_OVER_CURRENT_WARNING
             NO_BIT,  // FAULT_SENSOR_OVER_TEMP_146C_WARNING
         },
+    .fault_output_pins = 1,  // ADR
+    .fault_output_name = fault_output_name,
 };
 
 }  // namespace esphome::tas58xx

esphome/components/tas58xx/model_tas5825m.cpp

@@ -6,7 +6,7 @@ namespace esphome::tas58xx {
 
 // Remainder of the startup sequence, run after the reset in TAS58xx::init_(). Register 0x00 selects the page.
 // Based on the TI PurePath Console (PPC) export for "TAS5825M 2-Band DRC&AGL 2.0 96k".
-// Registers 0x46, 0x7D, 0x7E, page 1 register 0x51 and page 2 registers 0x1D, 0x19 are not documented in datasheet.
+// Registers 0x7D, 0x7E, page 1 register 0x51 and page 2 registers 0x1D, 0x19 are not documented in datasheet.
 static constexpr i2c::I2CRegValue STARTUP_SEQUENCE[] PROGMEM = {
     {0x03, 0x00},  // DEVICE_CTRL_2: deep sleep, the state the PPC sequence starts from
     {0x7D, 0x11},
@@ -17,20 +17,25 @@ static constexpr i2c::I2CRegValue STARTUP_SEQUENCE[] PROGMEM = {
     {0x1D, 0x00},
     {0x19, 0x80},
     {0x00, 0x00},  // Page 0
-    {0x46, 0x11},
+    {0x46, 0x11},  // DSP_CTRL: 96 kHz processing (bits 4-3 = 10), use default coefficients (bit 0 = 1)
     // PPC also writes 0x02 (DEVICE_CTRL_1) and 0x54 (AGAIN) here; init_() writes both from YAML
     {0x53, 0x01},  // ANA_CTRL: in phase, 100kHz bandwidth for high audio performance with Fsw=384kHz
     {0x03, 0x02},  // DEVICE_CTRL_2: Hi-Z
 
     // Additional register configuration
-    // GPIO1 is a dedicated pin on TAS5825M (separate from ADR), used as FAULTZ
-    {0x62, 0x0B},  // GPIO1_SEL: GPIO1 as FAULTZ
-    {0x60, 0x02},  // GPIO_CTRL: GPIO1 is output
     {0x77, 0x07},  // CBC_CONTROL: enable cycle-by-cycle current limit for warnings and faults
 };
 
 static const LogString *model_name() { return LOG_STR("TAS5825M"); }
 
+static const LogString *fault_output_name(uint8_t pin) {
+  if (pin == 0)
+    return LOG_STR("GPIO0");
+  if (pin == 1)
+    return LOG_STR("GPIO1");
+  return LOG_STR("GPIO2");
+}
+
 // An if chain rather than a switch: a switch table would land in rodata, which is RAM on ESP8266.
 static const LogString *fault_name(uint8_t index) {
   if (index == 0)
@@ -113,6 +118,8 @@ const ModelInfo TAS5825M_MODEL = {
                  // 25,  // FAULT_SENSOR_OVER_TEMP_122C_WARNING // not currently included
                  // 24,  // FAULT_SENSOR_OVER_TEMP_112C_WARNING // not currently included
         },
+    .fault_output_pins = 3,  // GPIO0, GPIO1, GPIO2 (ADR is an analog input only on TAS5825M)
+    .fault_output_name = fault_output_name,
 };
 
 }  // namespace esphome::tas58xx

esphome/components/tas58xx/tas58xx.cpp

@@ -20,6 +20,7 @@ static constexpr uint8_t TAS58XX_RESET_CTRL = 0x01;
 static constexpr uint8_t TAS58XX_RESET_CTRL_ALL = 0x11;  // Reset DSP/control port and registers
 static constexpr uint8_t TAS58XX_DEVICE_CTRL_1 = 0x02;
 static constexpr uint8_t TAS58XX_DEVICE_CTRL_1_PBTL = (1 << 2);
+static constexpr uint8_t TAS58XX_DEVICE_CTRL_1_1SPW = 0x01;  // DAMP_MOD = 01
 static constexpr uint8_t TAS58XX_DEVICE_CTRL_2 = 0x03;
 static constexpr uint8_t TAS58XX_DEVICE_CTRL_2_MUTE = (1 << 3);
 static constexpr uint8_t TAS58XX_CTRL_STATE_MASK = 0x03;  // DEVICE_CTRL_2 and POWER_STATE
@@ -33,6 +34,9 @@ static constexpr uint8_t TAS58XX_DIG_VOL_0DB = 0x30;
 static constexpr uint8_t TAS58XX_DIG_VOL_MINUS_103DB = 0xFE;
 static constexpr uint8_t TAS58XX_AGAIN = 0x54;  // 0x00 = 0 dB to 0x1F = -15.5 dB in 0.5 dB steps
 static constexpr uint8_t TAS58XX_AGAIN_MINUS_15_5DB = 0x1F;
+static constexpr uint8_t TAS58XX_GPIO_CTRL = 0x60;        // ADR_PIN_CTRL on TAS5805M: output enable, bit n for pin n
+static constexpr uint8_t TAS58XX_GPIO0_SEL = 0x61;        // ADR_PIN_CONFIG on TAS5805M: pin n is selected at 0x61 + n
+static constexpr uint8_t TAS58XX_GPIO_SEL_FAULTZ = 0x0B;  // pin function: FAULTZ output
 static constexpr uint8_t TAS58XX_POWER_STATE = 0x68;
 static constexpr uint8_t TAS58XX_CHAN_FAULT = 0x70;  // GLOBAL_FAULT1, GLOBAL_FAULT2 and OT_WARNING follow
 static constexpr uint8_t TAS58XX_FAULT_REGISTER_COUNT = 4;
@@ -98,12 +102,26 @@ bool TAS58xx::init_() {
     return false;
   }
 
-  // Setters are public, so keep the value inside the register range
+  // The I2C address is latched at power up, so ADR can now be an output. The pin function is written before the
+  // output enable, so the pin never drives another function.
+  if (this->fault_output_pin_ != FAULT_OUTPUT_NONE) {
+    // The setter is public, so only write this model's pins; YAML only allows the pins of the model
+    if (this->fault_output_pin_ >= this->model_->fault_output_pins) {
+      ESP_LOGW(TAG, "Invalid fault output index %u", this->fault_output_pin_);
+    } else if (!this->write_byte(TAS58XX_GPIO0_SEL + this->fault_output_pin_, TAS58XX_GPIO_SEL_FAULTZ) ||
+               !this->write_byte(TAS58XX_GPIO_CTRL, static_cast<uint8_t>(1 << this->fault_output_pin_))) {
+      ESP_LOGE(TAG, "I2C write failed during init");
+      return false;
+    }
+  }
+
+  // Setters are public, so keep the values inside the register ranges
   const uint8_t again =
       static_cast<uint8_t>(lroundf(clamp(-this->analog_gain_db_ * 2.0f, 0.0f, float{TAS58XX_AGAIN_MINUS_15_5DB})));
-  if (!this->write_byte(TAS58XX_DEVICE_CTRL_1, this->dac_mode_ == DAC_MODE_PBTL ? TAS58XX_DEVICE_CTRL_1_PBTL : 0) ||
-      !this->write_byte(TAS58XX_AGAIN, again) || !this->write_volume_() ||
-      !this->write_ctrl_state_(TAS58XX_CTRL_STATE_PLAY, this->is_muted_) ||
+  const uint8_t device_ctrl_1 = (this->dac_mode_ == DAC_MODE_PBTL ? TAS58XX_DEVICE_CTRL_1_PBTL : 0) |
+                                (this->modulation_ == MODULATION_1SPW_MODE ? TAS58XX_DEVICE_CTRL_1_1SPW : 0);
+  if (!this->write_byte(TAS58XX_DEVICE_CTRL_1, device_ctrl_1) || !this->write_byte(TAS58XX_AGAIN, again) ||
+      !this->write_volume_() || !this->write_ctrl_state_(TAS58XX_CTRL_STATE_PLAY, this->is_muted_) ||
       !this->write_byte(TAS58XX_FAULT_CLEAR, TAS58XX_FAULT_CLEAR_ANALOG)) {
     ESP_LOGE(TAG, "I2C write failed during init");
     return false;
@@ -263,6 +281,14 @@ void TAS58xx::dump_config() {
   } else {
     mixer_mode = LOG_STR("Stereo");
   }
+  const LogString *fault_output;
+  if (this->fault_output_pin_ == FAULT_OUTPUT_NONE) {
+    fault_output = LOG_STR("None");
+  } else if (this->fault_output_pin_ >= this->model_->fault_output_pins) {
+    fault_output = LOG_STR("Invalid");
+  } else {
+    fault_output = this->model_->fault_output_name(this->fault_output_pin_);
+  }
   ESP_LOGCONFIG(TAG,
                 "Audio Amplifier:\n"
                 "  Model: %s",
@@ -273,11 +299,14 @@ void TAS58xx::dump_config() {
   ESP_LOGCONFIG(TAG,
                 "  Analog Gain: %.1f dB\n"
                 "  DAC Mode: %s\n"
+                "  Modulation: %s\n"
                 "  Mixer Mode: %s\n"
-                "  Volume Range: %.1f dB to %.1f dB",
+                "  Volume Range: %.1f dB to %.1f dB\n"
+                "  Fault Output: %s",
                 this->analog_gain_db_,
                 this->dac_mode_ == DAC_MODE_PBTL ? LOG_STR_LITERAL("PBTL") : LOG_STR_LITERAL("BTL"),
-                LOG_STR_ARG(mixer_mode), this->volume_min_db_, this->volume_max_db_);
+                this->modulation_ == MODULATION_1SPW_MODE ? LOG_STR_LITERAL("1SPW") : LOG_STR_LITERAL("BD"),
+                LOG_STR_ARG(mixer_mode), this->volume_min_db_, this->volume_max_db_, LOG_STR_ARG(fault_output));
 #ifdef USE_BINARY_SENSOR
   LOG_BINARY_SENSOR("  ", "Any Fault", this->have_fault_binary_sensor_);
   for (auto *sensor : this->fault_binary_sensors_) {

esphome/components/tas58xx/tas58xx.h

@@ -22,6 +22,12 @@ enum DacMode : uint8_t {
   DAC_MODE_PBTL = 1,  // Parallel bridge tied load, one speaker
 };
 
+/// DEVICE_CTRL_1 DAMP_MOD values, the same on all models
+enum Modulation : uint8_t {
+  MODULATION_BD_MODE = 0,
+  MODULATION_1SPW_MODE = 1,
+};
+
 enum MixerMode : uint8_t {
   MIXER_MODE_STEREO = 0,
   MIXER_MODE_STEREO_INVERSE,
@@ -64,6 +70,8 @@ static_assert(
 
 /// ModelInfo::fault_sensor_bits value for a FaultSensor that the model does not have.
 static constexpr uint8_t NO_BIT = 0xFF;
+/// fault_output_pin_ value for no fault output
+static constexpr uint8_t FAULT_OUTPUT_NONE = 0xFF;
 
 /// Everything that differs between models of the family. One constant instance exists per model, see
 /// model_*.cpp, and each TAS58xx instance points to the one for its model.
@@ -91,6 +99,10 @@ struct ModelInfo {
   const LogString *(*fault_name)(uint8_t index);
   /// Bit index for each FaultSensor, NO_BIT used where the model does not have that fault bit
   uint8_t fault_sensor_bits[FAULT_SENSOR_COUNT];
+  /// Number of pins that can report FAULTZ: pin n is selected at 0x61 + n and enabled by bit n of 0x60
+  uint8_t fault_output_pins;
+  /// Name of FAULTZ pin n, for dump_config
+  const LogString *(*fault_output_name)(uint8_t pin);
 };
 
 #ifdef USE_TAS58XX_TAS5805M
@@ -127,7 +139,10 @@ class TAS58xx : public audio_dac::AudioDac, public PollingComponent, public i2c:
   void set_enable_pin(GPIOPin *enable_pin) { this->enable_pin_ = enable_pin; }
   void set_analog_gain(float analog_gain_db) { this->analog_gain_db_ = analog_gain_db; }
   void set_dac_mode(DacMode dac_mode) { this->dac_mode_ = dac_mode; }
+  /// pin: 0 to 2 for GPIOn on TAS5825M, 0 for ADR on TAS5805M; leave unset for no fault output
+  void set_fault_output(uint8_t pin) { this->fault_output_pin_ = pin; }
   void set_mixer_mode(MixerMode mixer_mode) { this->mixer_mode_ = mixer_mode; }
+  void set_modulation(Modulation modulation) { this->modulation_ = modulation; }
   void set_volume_min_db(float volume_min_db) { this->volume_min_db_ = volume_min_db; }
   void set_volume_max_db(float volume_max_db) { this->volume_max_db_ = volume_max_db; }
 
@@ -171,7 +186,9 @@ class TAS58xx : public audio_dac::AudioDac, public PollingComponent, public i2c:
   float volume_max_db_{24.0f};
   uint32_t logged_faults_{0};  // Fault bits as last logged, packed like the fault masks
   DacMode dac_mode_{DAC_MODE_BTL};
+  uint8_t fault_output_pin_{FAULT_OUTPUT_NONE};  // No fault output: the pin keeps its power on state
   MixerMode mixer_mode_{MIXER_MODE_STEREO};
+  Modulation modulation_{MODULATION_BD_MODE};
   uint8_t ctrl_state_{0};
   uint8_t power_state_{0xFF};  // Last POWER_STATE seen by update(), 0xFF until the first read
   bool mixer_written_{false};  // Mixer written since the last reset

esphome/config_validation.py

@@ -2744,8 +2744,13 @@ def url(value):
     raise Invalid("Expected a file scheme or a URL scheme with host")
 
 
-def git_ref(value):
-    if re.match(r"[a-zA-Z0-9_./-]+", value) is None:
+# Characters git never allows in a branch or tag name (git check-ref-format)
+GIT_REF_PATTERN = r"[^\s~^:?*\[\\]+"
+
+
+def git_ref(value: typing.Any) -> str:
+    value = string_strict(value)
+    if re.fullmatch(GIT_REF_PATTERN, value) is None:
         raise Invalid("Not a valid git ref")
     return value
 
@@ -3000,9 +3005,8 @@ def validate_source_shorthand(value):
     except Invalid:
         pass
     # Regex for GitHub repo name with optional branch/tag
-    # Note: git allows other branch/tag names as well, but never seen them used before
-    m = re.match(
-        r"github://(?:([a-zA-Z0-9\-]+)/([a-zA-Z0-9\-\._]+)(?:@([a-zA-Z0-9\-_.\./]+))?|pr#([0-9]+))",
+    m = re.fullmatch(
+        rf"github://(?:([a-zA-Z0-9\-]+)/([a-zA-Z0-9\-\._]+)(?:@({GIT_REF_PATTERN}))?|pr#([0-9]+))",
         value,
     )
     if m is None:

esphome/git.py

@@ -718,9 +718,9 @@ def _clone_or_update_locked(
     # compute the same cache key as this one.
     original_url = url
     if username is not None and password is not None:
-        url = url.replace(
-            "://", f"://{urllib.parse.quote(username)}:{urllib.parse.quote(password)}@"
-        )
+        user = urllib.parse.quote(username, safe="")
+        token = urllib.parse.quote(password, safe="")
+        url = url.replace("://", f"://{user}:{token}@")
 
     hash_dir_name = _compute_destination_path(key, domain).name
     repo_dir = _repo_entry_dir(key, domain, subpath)
@@ -1051,8 +1051,8 @@ class GitFile:
         """Parse a git shorthand URL into its components."""
         if not isinstance(shorthand, str):
             raise ValueError("Git shorthand must be a string")
-        m = re.match(
-            r"(?P<domain>[a-zA-Z0-9\-]+)://(?P<owner>[a-zA-Z0-9\-]+)/(?P<repo>[a-zA-Z0-9\-\._]+)/(?P<filename>[a-zA-Z0-9\-_.\./]+)(?:@(?P<ref>[a-zA-Z0-9\-_.\./]+))?(?:\?(?P<query>[a-zA-Z0-9\-_.\./]+))?",
+        m = re.fullmatch(
+            rf"(?P<domain>[a-zA-Z0-9\-]+)://(?P<owner>[a-zA-Z0-9\-]+)/(?P<repo>[a-zA-Z0-9\-\._]+)/(?P<filename>[a-zA-Z0-9\-_.\./]+)(?:@(?P<ref>{cv.GIT_REF_PATTERN}))?(?:\?(?P<query>[a-zA-Z0-9\-_.\./]+))?",
             shorthand,
         )
         if m is None:

esphome/idf_component.yml

@@ -2,7 +2,7 @@ dependencies:
   bblanchon/arduinojson:
     version: "7.4.3"
   esphome/dlms_parser:
-    version: 2.2.0
+    version: 2.2.2
   esphome/esp-audio-libs:
     version: 4.1.0
   esphome/esp-micro-speech-features:

esphome/loader.py

@@ -284,12 +284,17 @@ def _lookup_module(domain: str, exception: bool) -> ComponentManifest | None:
             _COMPONENT_CACHE[domain] = manif
         return manif
 
+    module_name = f"esphome.components.{domain}"
     try:
-        module = importlib.import_module(f"esphome.components.{domain}")
+        module = importlib.import_module(module_name)
     except ImportError as e:
         if exception:
             raise
-        if "No module named" in str(e):
+        if (
+            isinstance(e, ModuleNotFoundError)
+            and e.name is not None
+            and f"{module_name}.".startswith(f"{e.name}.")
+        ):
             _LOGGER.info(
                 "Unable to import component %s: %s", domain, str(e), exc_info=False
             )

platformio.ini

@@ -106,7 +106,7 @@ build_unflags =
 ; esp32 envs (which would double-include them).
 [common:idf-component-libs]
 lib_deps =
-    esphome/dlms_parser@2.2.0             ; dlms_meter
+    esphome/dlms_parser@2.2.2             ; dlms_meter
     bblanchon/ArduinoJson@7.4.3           ; json
     lvgl/lvgl@9.6.0                       ; lvgl
 

tests/component_tests/logger/test_logger.py

@@ -138,3 +138,26 @@ def test_task_log_buffer_size_unaligned_allowed_on_libretiny(
 ) -> None:
     set_core_config(PlatformFramework.BK72XX_ARDUINO)
     assert validate_task_log_buffer_alignment(641) == 641
+
+
+@pytest.mark.parametrize(
+    ("config", "log_v2"),
+    [
+        pytest.param("test_logger_idf6_esp_idf.yaml", True, id="native"),
+        pytest.param("test_logger_idf6_platformio.yaml", False, id="platformio"),
+    ],
+)
+def test_log_v2_only_on_native_toolchain(
+    generate_main: Callable[[str | Path], str],
+    config: str,
+    log_v2: bool,
+) -> None:
+    """PlatformIO links the bootloader with the app's build flags, so the wrap has no target there."""
+    from esphome.components.esp32 import KEY_ESP32, KEY_SDKCONFIG_OPTIONS
+
+    generate_main(f"tests/component_tests/logger/{config}")
+
+    assert ("-Wl,--wrap=esp_log_format" in CORE.build_flags) is log_v2
+    assert ("USE_ESP32_LOG_V2" in {d.name for d in CORE.defines}) is log_v2
+    sdkconfig = CORE.data[KEY_ESP32][KEY_SDKCONFIG_OPTIONS]
+    assert ("CONFIG_LOG_VERSION_2" in sdkconfig) is log_v2

tests/component_tests/logger/test_logger_idf6_esp_idf.yaml

@@ -0,0 +1,11 @@
+esphome:
+  name: test
+
+esp32:
+  board: esp32dev
+  toolchain: esp-idf
+  framework:
+    type: esp-idf
+    version: 6.1.0
+
+logger:

tests/component_tests/logger/test_logger_idf6_platformio.yaml

@@ -0,0 +1,12 @@
+esphome:
+  name: test
+
+esp32:
+  board: esp32dev
+  toolchain: platformio
+  framework:
+    type: esp-idf
+    version: 6.1.0
+    platform_version: 61.4.0-RC1
+
+logger:

tests/component_tests/tas58xx/test_tas58xx.py

@@ -0,0 +1,31 @@
+"""Tests that the TAS58xx fault_output and modulation defaults keep the existing behaviour."""
+
+from __future__ import annotations
+
+from collections.abc import Callable
+from pathlib import Path
+
+
+def test_tas58xx_defaults_keep_the_fault_pin_and_bd_modulation(
+    generate_main: Callable[[str | Path], str],
+) -> None:
+    """Without fault_output or modulation each model keeps its usual fault pin and BD modulation."""
+    main_cpp = generate_main(
+        "tests/component_tests/tas58xx/test_tas58xx_fault_output_modulation.yaml"
+    )
+
+    assert "amp_5805_default->set_fault_output(0);" in main_cpp
+    assert "amp_5825_default->set_fault_output(1);" in main_cpp
+    for amp in ("amp_5805_default", "amp_5825_default", "amp_5805_none"):
+        assert f"{amp}->set_modulation(tas58xx::MODULATION_BD_MODE);" in main_cpp
+
+
+def test_tas58xx_fault_output_none_leaves_the_pin_alone(
+    generate_main: Callable[[str | Path], str],
+) -> None:
+    """fault_output: none does not configure a fault pin."""
+    main_cpp = generate_main(
+        "tests/component_tests/tas58xx/test_tas58xx_fault_output_modulation.yaml"
+    )
+
+    assert "amp_5805_none->set_fault_output(" not in main_cpp

tests/component_tests/tas58xx/test_tas58xx_fault_output_modulation.yaml

@@ -0,0 +1,26 @@
+esphome:
+  name: test
+
+esp32:
+  board: esp32dev
+
+i2c:
+  id: i2c_bus
+  sda: 21
+  scl: 22
+
+audio_dac:
+  - platform: tas58xx
+    model: tas5805m
+    id: amp_5805_default
+    ignore_enable_pin_warning: true
+  - platform: tas58xx
+    model: tas5825m
+    id: amp_5825_default
+    ignore_enable_pin_warning: true
+  - platform: tas58xx
+    model: tas5805m
+    id: amp_5805_none
+    address: 0x2C
+    ignore_enable_pin_warning: true
+    fault_output: none

tests/components/microphone/test_data_callbacks.cpp

@@ -17,7 +17,7 @@ class TestMicrophone : public Microphone {
   void start() override {}
   void stop() override {}
 
-  void publish(std::span<const uint8_t> data, const audio::AudioStreamInfo &stream_info, int64_t capture_time_us) {
+  void publish(std::span<uint8_t> data, const audio::AudioStreamInfo &stream_info, int64_t capture_time_us) {
     this->publish_audio_(data, stream_info, capture_time_us);
   }
   bool has_callbacks() const { return this->has_data_callbacks_(); }
@@ -56,20 +56,24 @@ TEST(MicrophoneDataCallbacks, CallbackGetsDataFormatAndCaptureTime) {
   });
   EXPECT_TRUE(mic.has_callbacks());
 
-  mic.publish(SAMPLES, STEREO_48K, 123456);
+  std::vector<uint8_t> buffer = SAMPLES;
+  mic.publish(buffer, STEREO_48K, 123456);
   EXPECT_EQ(data, SAMPLES);
   EXPECT_EQ(stream_info, STEREO_48K);
   EXPECT_EQ(capture_time_us, 123456);
 }
 
-TEST(MicrophoneDataCallbacks, MutedCallbackGetsZeros) {
+TEST(MicrophoneDataCallbacks, MuteZeroesTheBufferInPlace) {
   TestMicrophone mic;
   std::vector<uint8_t> data;
   mic.add_data_callback([&](const AudioCapture &capture) { data.assign(capture.data.begin(), capture.data.end()); });
 
   mic.set_mute_state(true);
-  mic.publish(SAMPLES, STEREO_48K, 0);
-  EXPECT_EQ(data, std::vector<uint8_t>(SAMPLES.size(), 0));
+  std::vector<uint8_t> buffer = SAMPLES;
+  mic.publish(buffer, STEREO_48K, 0);
+  const std::vector<uint8_t> zeros(SAMPLES.size(), 0);
+  EXPECT_EQ(data, zeros);
+  EXPECT_EQ(buffer, zeros);
 }
 
 TEST(MicrophoneDataCallbacks, DataTriggerPassesACopy) {
@@ -115,4 +119,17 @@ TEST(MicrophoneDataCallbacks, DeprecatedCallUsesMicrophoneFormat) {
   EXPECT_EQ(capture_time_us, 0);
 }
 
+// Remove in 2027.5.0 with the deprecated DataCallbackManager::call(data)
+TEST(MicrophoneDataCallbacks, DeprecatedCallDeliversZerosWhileMuted) {
+  TestMicrophone mic;
+  std::vector<uint8_t> data;
+  mic.add_data_callback([&](const AudioCapture &capture) { data.assign(capture.data.begin(), capture.data.end()); });
+
+  mic.set_mute_state(true);
+  const std::vector<uint8_t> buffer = SAMPLES;
+  mic.publish_deprecated(buffer);
+  EXPECT_EQ(data, std::vector<uint8_t>(SAMPLES.size(), 0));
+  EXPECT_EQ(buffer, SAMPLES);
+}
+
 }  // namespace esphome::microphone::testing

tests/components/tas58xx/common.yaml

@@ -7,7 +7,9 @@ audio_dac:
     enable_pin: GPIO12
     analog_gain: -15.5dB
     dac_mode: btl
+    fault_output: adr
     mixer_mode: stereo
+    modulation: 1SPW_MODE
     volume_min_db: -60dB
     volume_max_db: 0dB
     update_interval: 1s

tests/components/tas58xx/validate.esp32-idf.yaml

@@ -9,3 +9,4 @@ audio_dac:
     dac_mode: PBTL
     mixer_mode: mono
     analog_gain: -3.5dB
+    fault_output: none

tests/integration/fixtures/uart_mock_ld2420_select_mode.yaml

@@ -0,0 +1,96 @@
+esphome:
+  name: uart-mock-ld2420-select-mode
+
+host:
+api:
+  batch_delay: 0ms  # Disable batching to receive all state updates
+logger:
+  level: VERBOSE
+
+external_components:
+  - source:
+      type: local
+      path: EXTERNAL_COMPONENT_PATH
+
+# Dummy uart entry to satisfy ld2420's DEPENDENCIES = ["uart"]
+# The actual UART bus used is the uart_mock component below
+uart:
+  baud_rate: 115200
+  port: /dev/null
+
+uart_mock:
+  id: mock_uart
+  baud_rate: 115200
+  auto_start: false
+  responses:
+    # Firmware v2.0.0 (1.5.4 or newer), so setup picks energy reporting
+    - expect_tx:
+        [0xFD, 0xFC, 0xFB, 0xFA, 0x02, 0x00, 0x00, 0x00, 0x04, 0x03, 0x02, 0x01]
+      inject_rx:
+        [
+          0xFD, 0xFC, 0xFB, 0xFA,
+          0x0C, 0x00,
+          0x00, 0x01,
+          0x00, 0x00,
+          0x06, 0x00,
+          0x76, 0x32, 0x2E, 0x30, 0x2E, 0x30,
+          0x04, 0x03, 0x02, 0x01,
+        ]
+
+    # Generic ACK for every other command
+    - expect_tx: [0x04, 0x03, 0x02, 0x01]
+      inject_rx:
+        [
+          0xFD, 0xFC, 0xFB, 0xFA,
+          0x04, 0x00,
+          0xFF, 0x01,
+          0x00, 0x00,
+          0x04, 0x03, 0x02, 0x01,
+        ]
+
+  injections:
+    # Sent after the select switched the module to Simple: "ON Range 0035\r\n" is only
+    # parsed while the component expects simple frames.
+    - delay: 100ms
+      inject_rx:
+        [
+          0x4F, 0x4E, 0x20, 0x52, 0x61, 0x6E, 0x67, 0x65, 0x20,
+          0x30, 0x30, 0x33, 0x35,
+          0x0D, 0x0A,
+        ]
+
+button:
+  - platform: template
+    name: "Start Scenario"
+    on_press:
+      - lambda: 'id(mock_uart).start_scenario();'
+  # A changed timeout gets apply_config_action() past its no-change check
+  - platform: template
+    name: "Apply Changed Config"
+    on_press:
+      - lambda: |-
+          id(ld2420_dev).new_config.timeout++;
+          id(ld2420_dev).apply_config_action();
+  - platform: template
+    name: "Inject Simple Frame"
+    on_press:
+      - lambda: |-
+          // "ON Range 0040\r\n"
+          id(mock_uart).inject_to_rx_buffer(std::vector<uint8_t>{
+              0x4F, 0x4E, 0x20, 0x52, 0x61, 0x6E, 0x67, 0x65, 0x20, 0x30, 0x30, 0x34, 0x30, 0x0D, 0x0A});
+
+ld2420:
+  id: ld2420_dev
+  uart_id: mock_uart
+
+sensor:
+  - platform: ld2420
+    ld2420_id: ld2420_dev
+    moving_distance:
+      name: "Moving Distance"
+
+select:
+  - platform: ld2420
+    ld2420_id: ld2420_dev
+    operating_mode:
+      name: "Operating Mode"

tests/integration/fixtures/uart_mock_ld2420_select_mode_nack.yaml

@@ -0,0 +1,73 @@
+esphome:
+  name: uart-mock-ld2420-mode-nack
+
+host:
+api:
+  batch_delay: 0ms  # Disable batching to receive all state updates
+logger:
+  level: VERBOSE
+
+external_components:
+  - source:
+      type: local
+      path: EXTERNAL_COMPONENT_PATH
+
+# Dummy uart entry to satisfy ld2420's DEPENDENCIES = ["uart"]
+# The actual UART bus used is the uart_mock component below
+uart:
+  baud_rate: 115200
+  port: /dev/null
+
+uart_mock:
+  id: mock_uart
+  baud_rate: 115200
+  responses:
+    # Firmware v2.0.0 (1.5.4 or newer), so setup picks energy reporting
+    - expect_tx:
+        [0xFD, 0xFC, 0xFB, 0xFA, 0x02, 0x00, 0x00, 0x00, 0x04, 0x03, 0x02, 0x01]
+      inject_rx:
+        [
+          0xFD, 0xFC, 0xFB, 0xFA,
+          0x0C, 0x00,
+          0x00, 0x01,
+          0x00, 0x00,
+          0x06, 0x00,
+          0x76, 0x32, 0x2E, 0x30, 0x2E, 0x30,
+          0x04, 0x03, 0x02, 0x01,
+        ]
+
+    # The simple system mode write is refused (error word 1)
+    - expect_tx:
+        [
+          0xFD, 0xFC, 0xFB, 0xFA, 0x08, 0x00, 0x12, 0x00,
+          0x00, 0x00, 0x64, 0x00, 0x00, 0x00, 0x04, 0x03, 0x02, 0x01,
+        ]
+      inject_rx:
+        [
+          0xFD, 0xFC, 0xFB, 0xFA,
+          0x04, 0x00,
+          0x12, 0x01,
+          0x01, 0x00,
+          0x04, 0x03, 0x02, 0x01,
+        ]
+
+    # Generic ACK for every other command
+    - expect_tx: [0x04, 0x03, 0x02, 0x01]
+      inject_rx:
+        [
+          0xFD, 0xFC, 0xFB, 0xFA,
+          0x04, 0x00,
+          0xFF, 0x01,
+          0x00, 0x00,
+          0x04, 0x03, 0x02, 0x01,
+        ]
+
+ld2420:
+  id: ld2420_dev
+  uart_id: mock_uart
+
+select:
+  - platform: ld2420
+    ld2420_id: ld2420_dev
+    operating_mode:
+      name: "Operating Mode"

tests/integration/fixtures/uart_mock_pipsolar_switches.yaml

@@ -0,0 +1,41 @@
+esphome:
+  name: uart-mock-pipsolar-switches
+
+host:
+api:
+  batch_delay: 0ms
+logger:
+  level: DEBUG
+
+external_components:
+  - source:
+      type: local
+      path: EXTERNAL_COMPONENT_PATH
+
+# Dummy uart entry to satisfy pipsolar's DEPENDENCIES = ["uart"]
+# The actual UART bus used is the uart_mock component below
+uart:
+  baud_rate: 2400
+  port: /dev/null
+
+uart_mock:
+  id: mock_uart
+  baud_rate: 2400
+  auto_start: false
+
+# No polling, so only the switch writes reach the command queue and no
+# polled status publishes the switch states
+pipsolar:
+  id: inverter0
+  uart_id: mock_uart
+  update_interval: never
+
+switch:
+  - platform: pipsolar
+    pipsolar_id: inverter0
+    output_source_priority_utility:
+      name: Priority Utility
+    input_voltage_range:
+      name: Input Voltage Range
+    pv_power_balance:
+      name: PV Power Balance

tests/integration/test_uart_mock_ld2420_select_mode.py

@@ -0,0 +1,128 @@
+"""Integration test for the LD2420 operating mode select with a mock UART.
+
+The module runs firmware v2.0.0, so it starts in energy reporting. Choosing Simple
+must write the simple system mode to the module and parse simple frames afterwards;
+choosing Normal again must write the energy system mode back.
+"""
+
+from __future__ import annotations
+
+import asyncio
+
+from aioesphomeapi import ButtonInfo, EntityState, SelectInfo, SelectState
+import pytest
+
+from .log_utils import LineWaiter
+from .state_utils import (
+    SensorStateCollector,
+    require_entity,
+    subscribe_after_initial_states,
+)
+from .types import APIClientConnectedFactory, RunCompiledFunction
+from .wait_utils import wait_or_fail
+
+# CMD_WRITE_SYS_PARAM (0x0012), parameter 0x0000 (system mode), then the mode and 0x0000
+WRITE_SIMPLE = "FD:FC:FB:FA:08:00:12:00:00:00:64:00:00:00:04:03:02:01"
+WRITE_ENERGY = "FD:FC:FB:FA:08:00:12:00:00:00:04:00:00:00:04:03:02:01"
+
+
+@pytest.mark.asyncio
+async def test_uart_mock_ld2420_select_mode(
+    yaml_config: str,
+    run_compiled: RunCompiledFunction,
+    api_client_connected: APIClientConnectedFactory,
+) -> None:
+    """The select switches the module between energy and simple reporting."""
+    waiter = LineWaiter()
+    collector = SensorStateCollector(sensor_names=["moving_distance"])
+    simple_frame_parsed = collector.add_waiter(
+        lambda: pytest.approx(35.0) in collector.sensor_states["moving_distance"]
+    )
+    second_frame_parsed = collector.add_waiter(
+        lambda: pytest.approx(40.0) in collector.sensor_states["moving_distance"]
+    )
+    modes: list[str] = []
+    back_to_normal = asyncio.Event()
+
+    def on_state(state: EntityState) -> None:
+        collector.on_state(state)
+        if isinstance(state, SelectState):
+            modes.append(state.state)
+            if modes[-2:] == ["Calibrate", "Normal"]:
+                back_to_normal.set()
+
+    async with (
+        run_compiled(yaml_config, line_callback=waiter.callback),
+        api_client_connected() as client,
+    ):
+        entities, _ = await client.list_entities_services()
+        collector.build_key_mapping(entities)
+        await subscribe_after_initial_states(client, entities, on_state=on_state)
+        mode = require_entity(entities, "operating_mode", SelectInfo)
+        apply_changed = require_entity(entities, "apply_changed_config", ButtonInfo)
+        # Setup wrote energy mode for this firmware
+        await waiter.wait_for("TX", WRITE_ENERGY)
+        writes_before = waiter.count(WRITE_ENERGY)
+
+        client.select_command(mode.key, "Simple")
+        await waiter.wait_for("TX", WRITE_SIMPLE)
+
+        client.button_command(
+            require_entity(entities, "start_scenario", ButtonInfo).key
+        )
+        await wait_or_fail(simple_frame_parsed, 3.0, "Simple frame was not parsed")
+
+        # Applying a changed config in Simple keeps Simple
+        client.button_command(apply_changed.key)
+        await waiter.wait_for("Reconfiguring")
+        inject = require_entity(entities, "inject_simple_frame", ButtonInfo)
+
+        async def inject_until_parsed() -> None:
+            # Simple reports are rate limited, so keep sending until one is published
+            while not second_frame_parsed.done():
+                client.button_command(inject.key)
+                await asyncio.sleep(0.2)
+
+        await wait_or_fail(inject_until_parsed(), 5.0, "Simple stopped after apply")
+        assert modes[-1] == "Simple"
+
+        client.select_command(mode.key, "Normal")
+        await waiter.wait_count(
+            WRITE_ENERGY, writes_before + 1, 3.0, "Normal did not write energy mode"
+        )
+        assert waiter.count(WRITE_ENERGY) == writes_before + 1
+
+        # Applying a changed config ends calibration
+        client.select_command(mode.key, "Calibrate")
+        client.button_command(apply_changed.key)
+        await wait_or_fail(back_to_normal, 5.0, "Apply did not end calibration")
+
+
+@pytest.mark.asyncio
+async def test_uart_mock_ld2420_select_mode_nack(
+    yaml_config: str,
+    run_compiled: RunCompiledFunction,
+    api_client_connected: APIClientConnectedFactory,
+) -> None:
+    """A refused Simple write puts the select back on the mode the module reports."""
+    waiter = LineWaiter()
+    states: list[str] = []
+    back_to_normal = asyncio.Event()
+
+    def on_state(state: EntityState) -> None:
+        if isinstance(state, SelectState):
+            states.append(state.state)
+            if states[-2:] == ["Simple", "Normal"]:
+                back_to_normal.set()
+
+    async with (
+        run_compiled(yaml_config, line_callback=waiter.callback),
+        api_client_connected() as client,
+    ):
+        entities, _ = await client.list_entities_services()
+        await subscribe_after_initial_states(client, entities, on_state=on_state)
+        mode = require_entity(entities, "operating_mode", SelectInfo)
+        client.select_command(mode.key, "Simple")
+        # Three tries of about a second each before the write is given up
+        await wait_or_fail(back_to_normal, 6.0, "Select did not go back to Normal")
+        assert waiter.count(WRITE_SIMPLE) == 3

tests/integration/test_uart_mock_pipsolar_switches.py

@@ -0,0 +1,94 @@
+"""Integration test for the pipsolar switches with mock UART.
+
+Each write queues the switch's on or off command on the hub, a direction with
+no command queues nothing, nothing is written at boot, and the write itself
+does not publish the switch state (the hub's polled status does).
+"""
+
+from __future__ import annotations
+
+import asyncio
+from pathlib import Path
+import re
+
+from aioesphomeapi import EntityState, SwitchInfo
+import pytest
+
+from .log_utils import LineWaiter
+from .state_utils import require_entity
+from .types import APIClientConnectedFactory, RunCompiledFunction
+
+QUEUED = re.compile(r"Command queued successfully: (\w+) at position")
+
+
+@pytest.mark.asyncio
+async def test_uart_mock_pipsolar_switches(
+    yaml_config: str,
+    run_compiled: RunCompiledFunction,
+    api_client_connected: APIClientConnectedFactory,
+) -> None:
+    """Switch writes queue their commands and publish nothing themselves."""
+    external_components_path = str(
+        Path(__file__).parent / "fixtures" / "external_components"
+    )
+    yaml_config = yaml_config.replace(
+        "EXTERNAL_COMPONENT_PATH", external_components_path
+    )
+    waiter = LineWaiter()
+
+    async with (
+        run_compiled(yaml_config, line_callback=waiter.callback),
+        api_client_connected() as client,
+    ):
+        entities, _ = await client.list_entities_services()
+        utility = require_entity(entities, "priority_utility", SwitchInfo)
+        voltage_range = require_entity(entities, "input_voltage_range", SwitchInfo)
+        balance = require_entity(entities, "pv_power_balance", SwitchInfo)
+
+        states: list[EntityState] = []
+        initial = asyncio.get_running_loop().create_future()
+
+        def on_state(state: EntityState) -> None:
+            states.append(state)
+            if len(states) == 3 and not initial.done():
+                initial.set_result(None)
+
+        client.subscribe_states(on_state)
+        await asyncio.wait_for(initial, timeout=5.0)
+        assert all(state.missing_state for state in states)
+        # Nothing is restored or written at boot
+        assert waiter.count(QUEUED) == 0
+
+        async def queued_after(key: int, on: bool) -> str:
+            future = waiter.expect(QUEUED)
+            client.switch_command(key, on)
+            match = await waiter.wait(future)
+            return match.group(1)
+
+        sent = waiter.expect("Sending command from queue: POP00")
+        assert await queued_after(utility.key, True) == "POP00"
+        await waiter.wait(sent)
+
+        # The utility switch has no off command, so the next queued command
+        # is the one written after it
+        future = waiter.expect(QUEUED)
+        client.switch_command(utility.key, False)
+        client.switch_command(balance.key, True)
+        assert (await waiter.wait(future)).group(1) == "PSPB1"
+        assert await queued_after(balance.key, False) == "PSPB0"
+        assert await queued_after(voltage_range.key, True) == "PGR01"
+        assert await queued_after(voltage_range.key, False) == "PGR00"
+
+        # A fresh connection's snapshot shows the writes left every switch unpublished
+        async with api_client_connected() as fresh:
+            snapshot: list[EntityState] = []
+            done = asyncio.get_running_loop().create_future()
+
+            def on_snapshot(state: EntityState) -> None:
+                snapshot.append(state)
+                if len(snapshot) == 3 and not done.done():
+                    done.set_result(None)
+
+            fresh.subscribe_states(on_snapshot)
+            await asyncio.wait_for(done, timeout=5.0)
+        assert all(state.missing_state for state in snapshot), snapshot

tests/unit_tests/components/esp32/test_framework_components.py

@@ -0,0 +1,28 @@
+"""Tests for the esp32 framework ``components:`` schema."""
+
+import pytest
+
+from esphome.components import esp32
+import esphome.config_validation as cv
+
+
+@pytest.mark.parametrize(
+    "source",
+    [
+        "https://github.com/owner/component.git",
+        "git@github.com:owner/component.git",
+    ],
+)
+def test_component_source_accepts_repository_url(source: str) -> None:
+    config = esp32.FRAMEWORK_SCHEMA(
+        {"components": [{"name": "owner/component", "source": source}]}
+    )
+    assert config["components"][0]["source"] == source
+
+
+@pytest.mark.parametrize("source", [1.0, ""])
+def test_component_source_rejects_invalid(source: object) -> None:
+    with pytest.raises(cv.Invalid):
+        esp32.FRAMEWORK_SCHEMA(
+            {"components": [{"name": "owner/component", "source": source}]}
+        )

tests/unit_tests/test_config_validation.py

@@ -3121,9 +3121,21 @@ def test_git_ref_valid() -> None:
     assert cv.git_ref("v1.2.3") == "v1.2.3"
 
 
-def test_git_ref_invalid() -> None:
+@pytest.mark.parametrize("ref", ["main", "release/v6.0", "feat+x", "a1b2c3d4"])
+def test_git_ref_valid_chars(ref: str) -> None:
+    assert cv.git_ref(ref) == ref
+
+
+@pytest.mark.parametrize("ref", ["main hi there", "a:b", "x~1", "", "main\n"])
+def test_git_ref_invalid(ref: str) -> None:
     with pytest.raises(Invalid, match="Not a valid git ref"):
-        cv.git_ref("!!!")
+        cv.git_ref(ref)
+
+
+@pytest.mark.parametrize("ref", [1.0, 2025, None])
+def test_git_ref_not_string(ref: object) -> None:
+    with pytest.raises(Invalid, match="Must be string"):
+        cv.git_ref(ref)
 
 
 def test_source_refresh_always() -> None:
@@ -3291,6 +3303,34 @@ def test_validate_source_shorthand_github_pr(setup_core: Path) -> None:
     assert result[CONF_REF] == "pull/1234/head"
 
 
+def test_validate_source_shorthand_github_ref_with_slash(setup_core: Path) -> None:
+    result = cv.validate_source_shorthand("github://user/repo@release/v1")
+    assert result[CONF_REF] == "release/v1"
+
+
+def test_validate_source_shorthand_github_ref_keeps_all_chars(
+    setup_core: Path,
+) -> None:
+    result = cv.validate_source_shorthand("github://user/repo@feat+x")
+    assert result[CONF_REF] == "feat+x"
+
+
+@pytest.mark.parametrize(
+    "value",
+    [
+        "github://esphome/esphome/esphome/components@dev",
+        "github://user/repo/",
+        "github://user/repo@main hi",
+        "github://pr#1234abc",
+    ],
+)
+def test_validate_source_shorthand_rejects_trailing_text(
+    setup_core: Path, value: str
+) -> None:
+    with pytest.raises(Invalid, match="not a file system path"):
+        cv.validate_source_shorthand(value)
+
+
 def test_validate_source_shorthand_invalid(setup_core: Path) -> None:
     with pytest.raises(Invalid, match="not a file system path"):
         cv.validate_source_shorthand("notvalid")

tests/unit_tests/test_git.py

@@ -10,6 +10,7 @@ import threading
 import time
 from typing import Any
 from unittest.mock import Mock, patch
+import urllib.parse
 
 from filelock import FileLock
 import pytest
@@ -2097,6 +2098,48 @@ def test_recovery_reclone_keeps_credentials_and_cache_key(
     assert clone_url.count("@") == 1
 
 
+def test_clone_credentials_with_slash_are_escaped(
+    tmp_path: Path, mock_run_git_command: Mock
+) -> None:
+    """A "/" in the username or password must be percent-encoded, or the
+    userinfo ends at the "/" and git reports the password in its error."""
+    CORE.config_path = tmp_path / "test.yaml"
+
+    url = "https://github.com/test/repo"
+    domain = "test"
+    repo_dir = _compute_repo_dir(url, None, domain)
+
+    def git_command_side_effect(
+        cmd: list[str], cwd: str | None = None, **kwargs: Any
+    ) -> str:
+        if _get_git_command_type(cmd) == "clone":
+            _simulate_cloned_repo(repo_dir)
+        return ""
+
+    mock_run_git_command.side_effect = git_command_side_effect
+
+    git.clone_or_update(
+        url=url,
+        ref=None,
+        refresh=TimePeriodSeconds(days=1),
+        domain=domain,
+        username="team/user",
+        password="ab/cd@ef",
+    )
+
+    clone_cmds = [
+        c[0][0]
+        for c in mock_run_git_command.call_args_list
+        if _get_git_command_type(c[0][0]) == "clone"
+    ]
+    assert clone_cmds
+    clone_url = clone_cmds[0][-2]
+    assert clone_url == "https://team%2Fuser:ab%2Fcd%40ef@github.com/test/repo"
+    assert urllib.parse.urlsplit(clone_url).hostname == "github.com"
+    redacted = git._redact_url_credentials(f"fatal: unable to access '{clone_url}/'")
+    assert redacted == "fatal: unable to access 'https://***@github.com/test/repo/'"
+
+
 def test_refresh_submodule_failure_recovers_then_raises(
     tmp_path: Path, mock_run_git_command: Mock
 ) -> None:
@@ -3289,6 +3332,26 @@ def test_git_file_from_shorthand_without_ref_or_query() -> None:
     assert gf == git.GitFile("codeberg.org", "owner", "repo", "file.yaml")
 
 
+def test_git_file_from_shorthand_keeps_whole_ref() -> None:
+    gf = git.GitFile.from_shorthand("github://owner/repo/file.yaml@feat+x?full_config")
+
+    assert gf.ref == "feat+x"
+    assert gf.query == "full_config"
+
+
+@pytest.mark.parametrize(
+    "shorthand",
+    [
+        "github://owner/repo/file.yaml@main hi",
+        "github://owner/repo/my file.yaml",
+        "github://owner/repo/file.yaml?full config",
+    ],
+)
+def test_git_file_from_shorthand_rejects_trailing_text(shorthand: str) -> None:
+    with pytest.raises(ValueError, match="not in expected"):
+        git.GitFile.from_shorthand(shorthand)
+
+
 def test_git_file_from_shorthand_requires_string() -> None:
     with pytest.raises(ValueError, match="must be a string"):
         git.GitFile.from_shorthand(123)

tests/unit_tests/test_loader.py

@@ -26,6 +26,7 @@ from esphome.loader import (
     clear_component_meta_finders,
     get_alias_metadata,
     get_component,
+    get_platform,
     install_meta_finder,
 )
 from tests.testing_helpers import ComponentManifestOverride
@@ -809,6 +810,44 @@ def test_lookup_module_import_error_missing_module_returns_none(
     assert "definitely_missing_component_xyz" not in _COMPONENT_CACHE
 
 
+def test_lookup_module_missing_platform_returns_none(
+    caplog: pytest.LogCaptureFixture,
+) -> None:
+    """A platform file that does not exist is "not found", not an error."""
+    with caplog.at_level(logging.INFO, logger="esphome.loader"):
+        assert get_platform("definitely_missing_platform_xyz", "template") is None
+    assert "Unable to import component template.definitely_missing_platform_xyz" in (
+        caplog.text
+    )
+    assert not [r for r in caplog.records if r.levelno >= logging.ERROR]
+
+
+def test_lookup_module_missing_dependency_is_logged_as_error(
+    tmp_path: Path, caplog: pytest.LogCaptureFixture
+) -> None:
+    """A component that exists but imports a missing package reports that
+    package as an error, instead of looking like a missing component."""
+    comp = tmp_path / "depfailcomp"
+    comp.mkdir()
+    (comp / "__init__.py").write_text("import definitely_missing_package_xyz\n")
+    saved = list(sys.meta_path)
+    try:
+        install_meta_finder(tmp_path)
+        with caplog.at_level(logging.INFO, logger="esphome.loader"):
+            assert get_component("depfailcomp") is None
+    finally:
+        sys.meta_path[:] = saved
+        for name in [
+            m for m in sys.modules if m.startswith("esphome.components.depfailcomp")
+        ]:
+            del sys.modules[name]
+    errors = [r for r in caplog.records if r.levelno >= logging.ERROR]
+    assert len(errors) == 1
+    assert errors[0].getMessage() == "Unable to import component depfailcomp:"
+    assert errors[0].exc_info is not None
+    assert errors[0].exc_info[1].name == "definitely_missing_package_xyz"
+
+
 def test_lookup_module_missing_module_raises_when_requested() -> None:
     """With ``exception=True`` the ImportError propagates."""
     with pytest.raises(ImportError):