Compare commits

..
36 changed files with 498 additions and 793 deletions

No files matched your search

+10 -4
View File
@@ -515,12 +515,18 @@ void CC1101Component::dump_config() {
}
void CC1101Component::begin_tx() {
if (this->state_.PKT_FORMAT == static_cast<uint8_t>(PacketFormat::PACKET_FORMAT_FIFO)) {
ESP_LOGW(TAG, "begin_tx is for async serial mode; use send_packet in packet mode");
return;
}
this->wake_up();
// Read the mode before the PKTCTRL0 write below overwrites it in state_
const bool packet_mode = this->state_.PKT_FORMAT == static_cast<uint8_t>(PacketFormat::PACKET_FORMAT_FIFO);
// Ensure Packet Format is 3 (Async Serial)
this->write_(Register::PKTCTRL0, 0x32);
ESP_LOGV(TAG, "Beginning TX sequence");
if (this->gdo0_pin_ != nullptr) {
// setup() only attaches the interrupt in packet mode. In async serial mode the pin may be
// shared with remote_receiver, and detaching here would remove the receiver's interrupt.
if (packet_mode) {
this->gdo0_pin_->detach_interrupt();
}
this->gdo0_pin_->pin_mode(gpio::FLAG_OUTPUT);
}
// Transition through IDLE to bypass CCA (Clear Channel Assessment) which can
@@ -63,25 +63,13 @@ void CST816Touchscreen::update_touches() {
uint8_t data[13];
if (!this->status_comm_result(this->read_bytes(REG_STATUS, data, sizeof data)))
return;
// The low nibble is the touch count. CST816/CST820 are single-touch;
// CST826/CST836 can report two points, but this driver only reads the first
// point. Some CST8xx controllers report an all-0xFF frame when idle or after
// disabling auto-sleep: the count lands above two and the coordinates are
// the 0xFFF sentinel, so both guards below reject it.
uint8_t num_of_touches = low_nibble(data[REG_TOUCH_NUM]);
uint8_t num_of_touches = data[REG_TOUCH_NUM] & 3;
if (num_of_touches == 0) {
return;
}
if (num_of_touches > 2) {
return;
}
uint16_t x = encode_uint16(low_nibble(data[REG_XPOS_HIGH]), data[REG_XPOS_LOW]);
uint16_t y = encode_uint16(low_nibble(data[REG_YPOS_HIGH]), data[REG_YPOS_LOW]);
if (x == 0x0FFF || y == 0x0FFF) {
return;
}
ESP_LOGV(TAG, "Read touch %d/%d", x, y);
this->add_raw_touch_position_(0, x, y);
}
@@ -1,16 +1,30 @@
#include "menu_item.h"
#include "esphome/core/progmem.h"
#include <cstdio>
namespace esphome::display_menu_base {
// Indexed by MenuItemType
PROGMEM_STRING_TABLE(MenuItemTypeStrings, "MENU_ITEM_LABEL", "MENU_ITEM_MENU", "MENU_ITEM_BACK", "MENU_ITEM_SELECT",
"MENU_ITEM_NUMBER", "MENU_ITEM_SWITCH", "MENU_ITEM_COMMAND", "MENU_ITEM_CUSTOM", "UNKNOWN");
const LogString *menu_item_type_to_string(MenuItemType type) {
return MenuItemTypeStrings::get_log_str(static_cast<uint8_t>(type), MenuItemTypeStrings::LAST_INDEX);
switch (type) {
case MenuItemType::MENU_ITEM_LABEL:
return LOG_STR("MENU_ITEM_LABEL");
case MenuItemType::MENU_ITEM_MENU:
return LOG_STR("MENU_ITEM_MENU");
case MenuItemType::MENU_ITEM_BACK:
return LOG_STR("MENU_ITEM_BACK");
case MenuItemType::MENU_ITEM_SELECT:
return LOG_STR("MENU_ITEM_SELECT");
case MenuItemType::MENU_ITEM_NUMBER:
return LOG_STR("MENU_ITEM_NUMBER");
case MenuItemType::MENU_ITEM_SWITCH:
return LOG_STR("MENU_ITEM_SWITCH");
case MenuItemType::MENU_ITEM_COMMAND:
return LOG_STR("MENU_ITEM_COMMAND");
case MenuItemType::MENU_ITEM_CUSTOM:
return LOG_STR("MENU_ITEM_CUSTOM");
default:
return LOG_STR("UNKNOWN");
}
}
void MenuItem::on_enter() { this->on_enter_callbacks_.call(); }
+26 -15
View File
@@ -94,6 +94,7 @@ UART_SELECTION_RP2040 = [USB_CDC, UART0, UART1]
UART_SELECTION_NRF52 = [USB_CDC, UART0]
# Read by device-builder
HARDWARE_UART_TO_UART_SELECTION = {
UART0: logger_ns.UART_SELECTION_UART0,
UART0_SWAP: logger_ns.UART_SELECTION_UART0_SWAP,
@@ -538,17 +539,17 @@ async def to_code(config: ConfigType) -> None:
cg.add(log.set_boot_log_level(tag, LOG_LEVELS[log_level]))
if CORE.is_esp32 or CORE.is_host:
cg.add(log.create_pthread_key())
# set_uart_selection() must be called before pre_setup() because
# pre_setup() switches on uart_ to decide which hardware to initialize
# (e.g. UART0 vs USB_SERIAL_JTAG). Without this, uart_ is still the
# default UART_SELECTION_UART0 and the wrong hardware gets initialized.
# uart_ is UART0 in C++ except on LibreTiny where it is DEFAULT; skip the
# setter when the config matches it.
cpp_default_uart = DEFAULT if CORE.is_libretiny else UART0
if (
hardware_uart := config.get(CONF_HARDWARE_UART)
) is not None and hardware_uart != cpp_default_uart:
cg.add(log.set_uart_selection(HARDWARE_UART_TO_UART_SELECTION[hardware_uart]))
if (hardware_uart := config.get(CONF_HARDWARE_UART)) is not None:
cg.add_define(f"USE_LOGGER_UART_SELECTION_{hardware_uart}")
cg.add_define(
"ESPHOME_LOGGER_UART_SELECTION",
cg.RawExpression(f"logger::UART_SELECTION_{hardware_uart}"),
)
# ESP8266 without serial logging never opens a port
cg.add_define(
"ESPHOME_LOGGER_UART_NAME",
"NONE" if CORE.is_esp8266 and baud_rate == 0 else hardware_uart,
)
# pre_setup() sets global_logger and must run before any other code
# that may call ESP_LOG* (e.g. setup_preferences contains ESP_LOGVV).
cg.add(log.pre_setup())
@@ -645,7 +646,6 @@ async def _late_logger_init(config: ConfigType) -> None:
add_idf_sdkconfig_option("CONFIG_ESP_CONSOLE_USB_CDC", True)
elif config[CONF_HARDWARE_UART] == USB_SERIAL_JTAG:
add_idf_sdkconfig_option("CONFIG_ESP_CONSOLE_USB_SERIAL_JTAG", True)
cg.add_define("USE_LOGGER_UART_SELECTION_USB_SERIAL_JTAG")
# Log V2 formats centrally in esp_log() (~4KB flash, ~180B RAM). 6.1
# adds CONSTRAINED_ENV_SAFE=n, keeping early/DRAM logs on
# esp_rom_printf instead of pulling ~1.2KB esp_rom_vprintf into IRAM.
@@ -663,10 +663,12 @@ async def _late_logger_init(config: ConfigType) -> None:
# --wrap: a strong definition collides; see logger_esp32.cpp
cg.add_build_flag("-Wl,--wrap=esp_log_format")
# Zephyr polls the USB port only when it logs there
if config.get(CONF_HARDWARE_UART) == USB_CDC and (
has_serial_logging or not CORE.is_nrf52
if (
CORE.using_zephyr
and has_serial_logging
and config[CONF_HARDWARE_UART] == USB_CDC
):
cg.add_define("USE_LOGGER_UART_SELECTION_USB_CDC")
cg.add_define("USE_LOGGER_ZEPHYR_CDC_LOOP")
# Define platform support flags for components that need auto-detection
try:
uart_selection(USB_SERIAL_JTAG)
@@ -884,6 +886,15 @@ def request_logger_level_listeners() -> None:
_request_log_listener_slot = cg.slot_counter("ESPHOME_LOG_MAX_LISTENERS")
def request_console() -> None:
"""Compile in Logger::console_read() and console_write(); call from to_code.
On ESP32 a USB_CDC logger only has a console where ESP-IDF sets CONFIG_ESP_CONSOLE_USB_CDC (targets with
USB OTG); elsewhere, such as the C3, C6 or H2, both do nothing. Host and Zephyr have no console API.
"""
cg.add_define("USE_LOGGER_CONSOLE")
def request_log_listener() -> None:
"""Reserve a log listener slot; call once per listener from to_code."""
cg.add_define("USE_LOG_LISTENERS")
+22 -3
View File
@@ -248,10 +248,10 @@ Logger::Logger(uint32_t baud_rate) : baud_rate_(baud_rate) {
#endif
}
#if defined(USE_ESPHOME_TASK_LOG_BUFFER) || (defined(USE_ZEPHYR) && defined(USE_LOGGER_UART_SELECTION_USB_CDC))
#if defined(USE_ESPHOME_TASK_LOG_BUFFER) || defined(USE_LOGGER_ZEPHYR_CDC_LOOP)
void Logger::loop() {
this->process_messages_();
#if defined(USE_ZEPHYR) && defined(USE_LOGGER_UART_SELECTION_USB_CDC)
#ifdef USE_LOGGER_ZEPHYR_CDC_LOOP
this->cdc_loop_();
#endif
}
@@ -278,7 +278,7 @@ void Logger::process_messages_() {
}
}
// Zephyr with USB CDC keeps the loop running for cdc_loop_()
#if !(defined(USE_ZEPHYR) && defined(USE_LOGGER_UART_SELECTION_USB_CDC))
#ifndef USE_LOGGER_ZEPHYR_CDC_LOOP
else {
// A concurrent enable_loop_soon_any_context() still wakes the next iteration
this->disable_loop();
@@ -371,6 +371,25 @@ static const LogString *get_log_level_str(uint8_t level) {
return LogLevelStrings::get_log_str(level, LogLevelStrings::LAST_INDEX);
}
#ifndef USE_HOST
const LogString *Logger::get_uart_selection_() {
#ifdef USE_LOGGER_UART_SELECTION_DEFAULT
// LibreTiny resolves DEFAULT to the board's port only when serial logging is on
if (this->baud_rate_ > 0) {
switch (this->get_uart()) {
case UART_SELECTION_UART0:
return LOG_STR("UART0");
case UART_SELECTION_UART1:
return LOG_STR("UART1");
default:
return LOG_STR("UART2");
}
}
#endif
return LOG_STR(ESPHOME_LOGGER_UART_NAME);
}
#endif
void Logger::dump_config() {
ESP_LOGCONFIG(TAG,
"Logger:\n"
+35 -10
View File
@@ -124,6 +124,9 @@ enum UARTSelection : uint8_t {
UART_SELECTION_UART0_SWAP,
#endif // USE_ESP8266
};
// The port chosen by hardware_uart, fixed at build time
static constexpr UARTSelection CONFIGURED_UART_SELECTION = ESPHOME_LOGGER_UART_SELECTION;
#endif // USE_ESP32 || USE_ESP8266 || USE_RP2 || USE_LIBRETINY || USE_ZEPHYR
/**
@@ -146,7 +149,7 @@ enum UARTSelection : uint8_t {
class Logger final : public Component {
public:
explicit Logger(uint32_t baud_rate);
#if defined(USE_ESPHOME_TASK_LOG_BUFFER) || (defined(USE_ZEPHYR) && defined(USE_LOGGER_UART_SELECTION_USB_CDC))
#if defined(USE_ESPHOME_TASK_LOG_BUFFER) || defined(USE_LOGGER_ZEPHYR_CDC_LOOP)
void loop() override;
#endif
#if defined(USE_RP2_CRASH_HANDLER) && defined(USE_LOGGER_UART_SELECTION_USB_CDC)
@@ -160,11 +163,11 @@ class Logger final : public Component {
#endif
#ifdef USE_ESP32
/// UART_NUM_0 when logging to USB
uart_port_t get_uart_num() const {
constexpr uart_port_t get_uart_num() const {
#if defined(USE_LOGGER_UART_SELECTION_USB_CDC) || defined(USE_LOGGER_UART_SELECTION_USB_SERIAL_JTAG)
return UART_NUM_0;
#else
return static_cast<uart_port_t>(this->uart_);
return static_cast<uart_port_t>(CONFIGURED_UART_SELECTION);
#endif
}
#endif
@@ -172,9 +175,35 @@ class Logger final : public Component {
void create_pthread_key() { pthread_key_create(&this->log_recursion_key_, nullptr); }
#endif
#if defined(USE_ESP32) || defined(USE_ESP8266) || defined(USE_RP2) || defined(USE_LIBRETINY) || defined(USE_ZEPHYR)
void set_uart_selection(UARTSelection uart_selection) { this->uart_ = uart_selection; }
/// Get the UART used by the logger.
UARTSelection get_uart() const { return this->uart_; }
#ifdef USE_LIBRETINY
// DEFAULT resolves to the board's default port
constexpr UARTSelection get_uart() const {
return CONFIGURED_UART_SELECTION == UART_SELECTION_DEFAULT ? static_cast<UARTSelection>(LT_UART_DEFAULT_SERIAL + 1)
: CONFIGURED_UART_SELECTION;
}
#else
constexpr UARTSelection get_uart() const { return CONFIGURED_UART_SELECTION; }
#endif
#endif
#ifdef USE_LOGGER_CONSOLE
// Raw bytes on the console port, without log framing; request with logger.request_console()
// console_write() returns the bytes written: a UART write blocks until all are queued, but a USB write can stop
// short when the host is not reading (USB Serial/JTAG gives up after 20 ms)
#if defined(USE_ARDUINO) && !defined(USE_ESP32)
size_t console_write(const uint8_t *data, size_t len) { return this->hw_serial_->write(data, len); }
bool console_read(uint8_t &byte) {
int c = this->hw_serial_->read();
if (c < 0)
return false;
byte = c;
return true;
}
#elif defined(USE_ESP32)
size_t console_write(const uint8_t *data, size_t len);
/// Non-blocking read of one byte; false if none is waiting.
bool console_read(uint8_t &byte);
#endif
#endif
/// Set the default log level for this logger.
@@ -251,7 +280,7 @@ class Logger final : public Component {
void log_vprintf_non_main_thread_(uint8_t level, const char *tag, int line, const char *format, va_list args,
const char *thread_name);
#endif
#if defined(USE_ZEPHYR) && defined(USE_LOGGER_UART_SELECTION_USB_CDC)
#ifdef USE_LOGGER_ZEPHYR_CDC_LOOP
void cdc_loop_();
#endif
void process_messages_();
@@ -411,10 +440,6 @@ class Logger final : public Component {
bool boot_log_done_{false}; // Set on first replay; stops further capture
#endif
uint8_t current_level_{ESPHOME_LOG_LEVEL_VERY_VERBOSE};
#if defined(USE_ESP32) || defined(USE_ESP8266) || defined(USE_RP2) || defined(USE_LIBRETINY) || defined(USE_ZEPHYR)
// 0 is UART0, or DEFAULT on LibreTiny; must match cpp_default_uart in __init__.py
UARTSelection uart_{};
#endif
bool main_task_recursion_guard_{false}; // Guards tx_buffer_ on the main loop
#ifdef USE_LIBRETINY
bool non_main_task_recursion_guard_{false}; // Shared guard for all non-main tasks on LibreTiny
+35 -37
View File
@@ -17,6 +17,10 @@
#include <driver/usb_serial_jtag_vfs.h>
#endif
#endif
// The logger accepts USB_CDC on targets without USB OTG (C3, C6, H2, ...), where IDF has no CDC console
#if defined(USE_LOGGER_CONSOLE) && defined(USE_LOGGER_UART_SELECTION_USB_CDC) && defined(CONFIG_ESP_CONSOLE_USB_CDC)
#include <esp_private/usb_console.h>
#endif
#if defined(CONFIG_PM_ENABLE) && defined(CONFIG_FREERTOS_USE_TICKLESS_IDLE) && \
(ESP_IDF_VERSION >= ESP_IDF_VERSION_VAL(6, 0, 0))
#include "esp_sleep.h"
@@ -73,6 +77,7 @@ static void init_usb_serial_jtag() {
}
#endif
#if !defined(USE_LOGGER_UART_SELECTION_USB_CDC) && !defined(USE_LOGGER_UART_SELECTION_USB_SERIAL_JTAG)
static void init_uart(uart_port_t uart_num, uint32_t baud_rate, int tx_buffer_size) {
uart_config_t uart_config{};
uart_config.baud_rate = (int) baud_rate;
@@ -97,6 +102,7 @@ static void init_uart(uart_port_t uart_num, uint32_t baud_rate, int tx_buffer_si
esp_sleep_set_console_uart_handling_mode(ESP_SLEEP_ALWAYS_FLUSH_UART);
#endif
}
#endif
// get_uart_num() and pre_setup() cast the selection straight to a port
static_assert(static_cast<int>(UART_SELECTION_UART0) == static_cast<int>(UART_NUM_0) &&
@@ -107,26 +113,11 @@ static_assert(static_cast<int>(UART_SELECTION_UART2) == static_cast<int>(UART_NU
void Logger::pre_setup() {
if (this->baud_rate_ > 0) {
switch (this->uart_) {
case UART_SELECTION_UART0:
case UART_SELECTION_UART1:
#ifdef USE_ESP32_VARIANT_ESP32
case UART_SELECTION_UART2:
#endif
init_uart(static_cast<uart_port_t>(this->uart_), this->baud_rate_, ESPHOME_LOGGER_TX_BUFFER_SIZE);
break;
#ifdef USE_LOGGER_USB_CDC
case UART_SELECTION_USB_CDC:
break;
#endif
#ifdef USE_LOGGER_USB_SERIAL_JTAG
case UART_SELECTION_USB_SERIAL_JTAG:
#ifdef USE_LOGGER_UART_SELECTION_USB_SERIAL_JTAG
init_usb_serial_jtag();
init_usb_serial_jtag();
#elif !defined(USE_LOGGER_UART_SELECTION_USB_CDC)
init_uart(this->get_uart_num(), this->baud_rate_, ESPHOME_LOGGER_TX_BUFFER_SIZE);
#endif
break;
#endif
}
}
global_logger = this;
@@ -138,29 +129,36 @@ void Logger::pre_setup() {
#endif
}
const LogString *Logger::get_uart_selection_() {
switch (this->uart_) {
case UART_SELECTION_UART0:
return LOG_STR("UART0");
case UART_SELECTION_UART1:
return LOG_STR("UART1");
#ifdef USE_ESP32_VARIANT_ESP32
case UART_SELECTION_UART2:
return LOG_STR("UART2");
#ifdef USE_LOGGER_CONSOLE
size_t Logger::console_write(const uint8_t *data, size_t len) {
int written = 0;
#if defined(USE_LOGGER_UART_SELECTION_USB_CDC)
#ifdef CONFIG_ESP_CONSOLE_USB_CDC // keep: not set without USB OTG, see the include above
written = esp_usb_console_write_buf(reinterpret_cast<const char *>(data), len);
#endif
#ifdef USE_LOGGER_USB_CDC
case UART_SELECTION_USB_CDC:
return LOG_STR("USB_CDC");
#elif defined(USE_LOGGER_UART_SELECTION_USB_SERIAL_JTAG)
written = usb_serial_jtag_write_bytes(data, len, pdMS_TO_TICKS(20));
#else
written = uart_write_bytes(this->get_uart_num(), data, len);
#endif
#ifdef USE_LOGGER_USB_SERIAL_JTAG
case UART_SELECTION_USB_SERIAL_JTAG:
return LOG_STR("USB_SERIAL_JTAG");
#endif
default:
return LOG_STR("UNKNOWN");
}
return written > 0 ? written : 0;
}
bool Logger::console_read(uint8_t &byte) {
#if defined(USE_LOGGER_UART_SELECTION_USB_CDC)
#ifdef CONFIG_ESP_CONSOLE_USB_CDC // keep: not set without USB OTG, see the include above
return esp_usb_console_available_for_read() && esp_usb_console_read_buf(reinterpret_cast<char *>(&byte), 1) == 1;
#else
return false;
#endif
#elif defined(USE_LOGGER_UART_SELECTION_USB_SERIAL_JTAG)
return usb_serial_jtag_read_bytes(&byte, 1, 0) > 0;
#else
return uart_read_bytes(this->get_uart_num(), &byte, 1, 0) > 0;
#endif
}
#endif
#ifdef USE_CRASH_HANDLER
bool crash_log_pending() { return esp32::crash_handler_has_data(); }
void log_crash_to_client() {
+3 -16
View File
@@ -14,9 +14,9 @@ void Logger::pre_setup() {
#if defined(USE_ESP8266_LOGGER_SERIAL)
this->hw_serial_ = &Serial;
Serial.begin(this->baud_rate_);
if (this->uart_ == UART_SELECTION_UART0_SWAP) {
Serial.swap();
}
#ifdef USE_LOGGER_UART_SELECTION_UART0_SWAP
Serial.swap();
#endif
Serial.setDebugOutput(ESPHOME_LOG_LEVEL >= ESPHOME_LOG_LEVEL_VERBOSE);
#elif defined(USE_ESP8266_LOGGER_SERIAL1)
this->hw_serial_ = &Serial1;
@@ -35,19 +35,6 @@ void Logger::pre_setup() {
#endif
}
const LogString *Logger::get_uart_selection_() {
#if defined(USE_ESP8266_LOGGER_SERIAL)
if (this->uart_ == UART_SELECTION_UART0_SWAP) {
return LOG_STR("UART0_SWAP");
}
return LOG_STR("UART0");
#elif defined(USE_ESP8266_LOGGER_SERIAL1)
return LOG_STR("UART1");
#else
return LOG_STR("NONE");
#endif
}
#ifdef USE_CRASH_HANDLER
bool crash_log_pending() { return esp8266::crash_handler_has_data(); }
void log_crash_to_client() { esp8266::crash_handler_log(); }
+1 -1
View File
@@ -9,7 +9,7 @@ void HOT Logger::write_msg_(const char *msg, uint16_t len) {
char buffer[TIMESTAMP_LEN + ESPHOME_LOGGER_TX_BUFFER_SIZE + HEADROOM];
time_t rawtime;
::time(&rawtime);
time(&rawtime);
struct tm timeinfo;
localtime_r(&rawtime, &timeinfo); // Thread-safe version
size_t pos = strftime(buffer, TIMESTAMP_LEN + 1, "[%H:%M:%S]", &timeinfo);
+20 -51
View File
@@ -12,45 +12,28 @@ ESPHOME_LOG_TAG(TAG, "logger");
void Logger::pre_setup() {
if (this->baud_rate_ > 0) {
switch (this->uart_) {
#if LT_HW_UART0
case UART_SELECTION_UART0:
this->hw_serial_ = &Serial0;
libretiny::ensure_serial_handle(0);
Serial0.begin(this->baud_rate_);
break;
#endif
#if LT_HW_UART1
case UART_SELECTION_UART1:
this->hw_serial_ = &Serial1;
libretiny::ensure_serial_handle(1);
Serial1.begin(this->baud_rate_);
break;
#endif
#if LT_HW_UART2
case UART_SELECTION_UART2:
this->hw_serial_ = &Serial2;
libretiny::ensure_serial_handle(2);
Serial2.begin(this->baud_rate_);
break;
#endif
default:
this->hw_serial_ = &Serial;
Serial.begin(this->baud_rate_);
if (this->uart_ != UART_SELECTION_DEFAULT) {
ESP_LOGW(TAG, " The chosen logger UART port is not available on this board."
"The default port was used instead.");
}
break;
#if defined(USE_LOGGER_UART_SELECTION_UART0) && LT_HW_UART0
this->hw_serial_ = &Serial0;
libretiny::ensure_serial_handle(0);
Serial0.begin(this->baud_rate_);
#elif defined(USE_LOGGER_UART_SELECTION_UART1) && LT_HW_UART1
this->hw_serial_ = &Serial1;
libretiny::ensure_serial_handle(1);
Serial1.begin(this->baud_rate_);
#elif defined(USE_LOGGER_UART_SELECTION_UART2) && LT_HW_UART2
this->hw_serial_ = &Serial2;
libretiny::ensure_serial_handle(2);
Serial2.begin(this->baud_rate_);
#else
this->hw_serial_ = &Serial;
Serial.begin(this->baud_rate_);
if (CONFIGURED_UART_SELECTION != UART_SELECTION_DEFAULT) {
ESP_LOGW(TAG, " The chosen logger UART port is not available on this board."
"The default port was used instead.");
}
#endif
// change lt_log() port to match default Serial
if (this->uart_ == UART_SELECTION_DEFAULT) {
this->uart_ = (UARTSelection) (LT_UART_DEFAULT_SERIAL + 1);
lt_log_set_port(LT_UART_DEFAULT_SERIAL);
} else {
lt_log_set_port(this->uart_ - 1);
}
lt_log_set_port(this->get_uart() - 1);
}
global_logger = this;
@@ -60,20 +43,6 @@ void Logger::pre_setup() {
#endif
}
const LogString *Logger::get_uart_selection_() {
switch (this->uart_) {
case UART_SELECTION_DEFAULT:
return LOG_STR("DEFAULT");
case UART_SELECTION_UART0:
return LOG_STR("UART0");
case UART_SELECTION_UART1:
return LOG_STR("UART1");
case UART_SELECTION_UART2:
default:
return LOG_STR("UART2");
}
}
#ifdef USE_LIBRETINY_CRASH_HANDLER
bool crash_log_pending() { return libretiny::crash_handler_has_data(); }
void log_crash_to_client() { libretiny::crash_handler_log(); }
+10 -27
View File
@@ -26,20 +26,16 @@ void Logger::setup() {
void Logger::pre_setup() {
if (this->baud_rate_ > 0) {
switch (this->uart_) {
case UART_SELECTION_UART0:
this->hw_serial_ = &Serial1;
Serial1.begin(this->baud_rate_);
break;
case UART_SELECTION_UART1:
this->hw_serial_ = &Serial2;
Serial2.begin(this->baud_rate_);
break;
case UART_SELECTION_USB_CDC:
this->hw_serial_ = &Serial;
Serial.begin(this->baud_rate_);
break;
}
#if defined(USE_LOGGER_UART_SELECTION_USB_CDC)
this->hw_serial_ = &Serial;
Serial.begin(this->baud_rate_);
#elif defined(USE_LOGGER_UART_SELECTION_UART1)
this->hw_serial_ = &Serial2;
Serial2.begin(this->baud_rate_);
#else
this->hw_serial_ = &Serial1;
Serial1.begin(this->baud_rate_);
#endif
}
global_logger = this;
ESP_LOGI(TAG, "Log initialized");
@@ -49,19 +45,6 @@ void Logger::pre_setup() {
#endif
}
const LogString *Logger::get_uart_selection_() {
switch (this->uart_) {
case UART_SELECTION_UART0:
return LOG_STR("UART0");
case UART_SELECTION_UART1:
return LOG_STR("UART1");
case UART_SELECTION_USB_CDC:
return LOG_STR("USB_CDC");
default:
return LOG_STR("UNKNOWN");
}
}
#ifdef USE_CRASH_HANDLER
bool crash_log_pending() { return rp2::crash_handler_has_data(); }
void log_crash_to_client() { rp2::crash_handler_log(); }
+13 -34
View File
@@ -42,7 +42,7 @@ __attribute__((section(".noinit"))) struct {
ESPHOME_LOG_TAG(TAG, "logger");
#ifdef USE_LOGGER_UART_SELECTION_USB_CDC
#ifdef USE_LOGGER_ZEPHYR_CDC_LOOP
void Logger::cdc_loop_() {
if (this->uart_dev_ == nullptr) {
return;
@@ -75,25 +75,19 @@ void Logger::pre_setup() {
#ifdef CONFIG_SERIAL
if (this->baud_rate_ > 0) {
const struct device *uart_dev = nullptr;
switch (this->uart_) {
case UART_SELECTION_UART0: // NOLINT(bugprone-branch-clone)
uart_dev = DEVICE_DT_GET_OR_NULL(DT_NODELABEL(ESPHOME_LOGGER_UART0_NODE));
break;
case UART_SELECTION_UART1:
uart_dev = DEVICE_DT_GET_OR_NULL(DT_NODELABEL(uart1));
break;
#ifdef USE_LOGGER_USB_CDC
case UART_SELECTION_USB_CDC:
#if defined(USE_LOGGER_UART_SELECTION_USB_CDC)
#if defined(CONFIG_USB_DEVICE_STACK) || defined(CONFIG_USB_DEVICE_STACK_NEXT)
uart_dev = DEVICE_DT_GET_OR_NULL(DT_NODELABEL(cdc_acm_uart0));
if (device_is_ready(uart_dev)) {
// Nothing can log this early, and the logger has no output without USB anyway
zephyr::usb_device_enable();
}
#endif
break;
#endif
uart_dev = DEVICE_DT_GET_OR_NULL(DT_NODELABEL(cdc_acm_uart0));
if (device_is_ready(uart_dev)) {
// Nothing can log this early, and the logger has no output without USB anyway
zephyr::usb_device_enable();
}
#endif
#elif defined(USE_LOGGER_UART_SELECTION_UART1)
uart_dev = DEVICE_DT_GET_OR_NULL(DT_NODELABEL(uart1));
#else
uart_dev = DEVICE_DT_GET_OR_NULL(DT_NODELABEL(ESPHOME_LOGGER_UART0_NODE));
#endif
if (device_is_ready(uart_dev)) {
this->uart_dev_ = uart_dev;
#if defined(USE_LOGGER_WAIT_FOR_CDC) && defined(USE_LOGGER_UART_SELECTION_USB_CDC)
@@ -117,7 +111,7 @@ void Logger::pre_setup() {
this->dump_crash_();
#endif
// Nobody reads a USB port this early; cdc_loop_() reports the dump once the port is opened
#if defined(USE_CRASH_HANDLER) && !defined(USE_LOGGER_UART_SELECTION_USB_CDC)
#if defined(USE_CRASH_HANDLER) && !defined(USE_LOGGER_ZEPHYR_CDC_LOOP)
// Without a UART (baud_rate: 0, or one that did not come up) nothing reaches the console
if (this->uart_dev_ != nullptr)
log_crash_to_client();
@@ -139,21 +133,6 @@ void HOT Logger::write_msg_(const char *msg, uint16_t len) {
}
}
const LogString *Logger::get_uart_selection_() {
switch (this->uart_) {
case UART_SELECTION_UART0:
return LOG_STR("UART0");
case UART_SELECTION_UART1:
return LOG_STR("UART1");
#ifdef USE_LOGGER_USB_CDC
case UART_SELECTION_USB_CDC:
return LOG_STR("USB_CDC");
#endif
default:
return LOG_STR("UNKNOWN");
}
}
static constexpr uint8_t REASON_BUF_SIZE = 32;
static const char *reason_to_str(unsigned int reason, char *buf) {
@@ -1,5 +1,4 @@
#include "mitsubishi_cn105.h"
#include "esphome/core/progmem.h"
#include <algorithm>
#include <array>
@@ -532,13 +531,32 @@ void MitsubishiCN105::apply_settings_() {
this->send_packet_(make_packet(PACKET_TYPE_WRITE_SETTINGS_REQUEST, payload));
}
// Indexed by State
PROGMEM_STRING_TABLE(StateStrings, "Not connected", "Connecting", "Connected", "UpdatingStatus", "StatusUpdated",
"DeferredStatusRequest", "ScheduleNextStatusUpdate", "WaitingForScheduledStatusUpdate",
"ApplyingSettings", "SettingsApplied", "ReadTimeout", "Unknown");
const LogString *MitsubishiCN105::state_to_string(State state) {
return StateStrings::get_log_str(static_cast<uint8_t>(state), StateStrings::LAST_INDEX);
switch (state) {
case State::NOT_CONNECTED:
return LOG_STR("Not connected");
case State::CONNECTING:
return LOG_STR("Connecting");
case State::CONNECTED:
return LOG_STR("Connected");
case State::UPDATING_STATUS:
return LOG_STR("UpdatingStatus");
case State::STATUS_UPDATED:
return LOG_STR("StatusUpdated");
case State::DEFERRED_STATUS_REQUEST:
return LOG_STR("DeferredStatusRequest");
case State::SCHEDULE_NEXT_STATUS_UPDATE:
return LOG_STR("ScheduleNextStatusUpdate");
case State::WAITING_FOR_SCHEDULED_STATUS_UPDATE:
return LOG_STR("WaitingForScheduledStatusUpdate");
case State::APPLYING_SETTINGS:
return LOG_STR("ApplyingSettings");
case State::SETTINGS_APPLIED:
return LOG_STR("SettingsApplied");
case State::READ_TIMEOUT:
return LOG_STR("ReadTimeout");
}
return LOG_STR("Unknown");
}
template<typename Callback>
+39 -117
View File
@@ -1,5 +1,4 @@
from collections.abc import Callable
import logging
from esphome import automation
import esphome.codegen as cg
@@ -9,8 +8,6 @@ import esphome.config_validation as cv
from esphome.const import CONF_DURATION, CONF_ID, CONF_MODE, CONF_VOLTAGE
from esphome.types import ConfigType
_LOGGER = logging.getLogger(__name__)
CODEOWNERS = ["@tomaszduda23"]
DEPENDENCIES = ["i2c"]
DOMAIN = "npm1300"
@@ -45,18 +42,20 @@ NPM1300_CHILD_SCHEMA = cv.Schema(
{cv.GenerateID(CONF_NPM1300_ID): cv.use_id(NPM1300Component)}
)
NPM1300Status = npm1300_ns.struct("NPM1300Status")
# The status registers read on each update
# Status registers read on each update: VBUSINSTATUS, BCHGCHARGESTATUS and BCHGERRREASON
STATUS_PUBLISHER = cg.HubFunction(
"status",
cg.void,
[(NPM1300Status.operator("const").operator("ref"), "status")],
[
(cg.uint8, "vbus_status"),
(cg.uint8, "charge_status"),
(cg.uint8, "error_reason"),
],
define="USE_NPM1300_STATUS_PUBLISHER",
)
STATUS = STATUS_PUBLISHER.param("status")
VBUS_STATUS = STATUS.vbus
CHARGE_STATUS = STATUS.charge
ERROR_REASON = STATUS.error_reason
VBUS_STATUS = STATUS_PUBLISHER.param("vbus_status")
CHARGE_STATUS = STATUS_PUBLISHER.param("charge_status")
ERROR_REASON = STATUS_PUBLISHER.param("error_reason")
# The ADC results and the amperes per code of the battery current
DATA_PUBLISHER = cg.HubFunction(
"data",
@@ -78,10 +77,7 @@ OUTPUTS = NPM1300Output.options(
# Written for a field the YAML leaves out
NPM1300_UNSET = 0xFF
# ADCNTCRSEL codes, by kiloohms
THERMISTOR_NONE = "none"
THERMISTOR_RESISTANCES = {10: 1, 47: 2, 100: 3}
# B25/50 of the thermistors the product specification lists for each resistance, by kiloohms
THERMISTOR_BETAS = {10: 3380, 47: 4050, 100: 4250}
LDO_MODES = {"load_switch": 0, "ldo": 1}
TERMINATION_CURRENTS = {"10%": 0, "20%": 1}
# BCHGVTRICKLESEL, by millivolts
@@ -105,13 +101,14 @@ def _one_of_units(
validator: Callable[[object], float],
allowed: list[int],
unit: str,
scale: float = 1000,
) -> Callable[[object], float]:
"""Validate a quantity with `validator` and accept only the listed values, given in thousandths of `unit`."""
"""Validate a quantity with `validator` and accept only the listed values, given in units * `scale`."""
def validate(value: object) -> float:
value = validator(value)
if _millis(value) not in allowed:
options = ", ".join(f"{v / 1000:g}{unit}" for v in allowed)
if round(value * scale) not in allowed:
options = ", ".join(f"{v / scale:g}{unit}" for v in allowed)
raise cv.Invalid(f"Must be one of {options}")
return value
@@ -138,23 +135,6 @@ def _stepped(
return validate
def _thermistor_resistance(value: object) -> float | str:
if isinstance(value, str) and value.lower() == THERMISTOR_NONE:
return THERMISTOR_NONE
value = cv.resistance(value)
if round(value) not in (kilohms * 1000 for kilohms in THERMISTOR_RESISTANCES):
options = ", ".join(f"{kilohms}kOhm" for kilohms in THERMISTOR_RESISTANCES)
raise cv.Invalid(f"Must be one of {options} or {THERMISTOR_NONE}")
return value
def thermistor_beta(config: ConfigType) -> int:
"""The B constant of the hub's thermistor: the configured one, or the one listed for its resistance."""
if (beta := config.get(CONF_THERMISTOR_BETA)) is not None:
return beta
return THERMISTOR_BETAS[round(config[CONF_THERMISTOR_RESISTANCE] / 1000)]
OUTPUT_VOLTAGE = _stepped(cv.voltage, 1000, 3300, 100, "V")
VBUS_CURRENT_LIMIT = _stepped(cv.current, 100, 1500, 100, "A")
@@ -170,58 +150,15 @@ LDO_SCHEMA = BUCK_SCHEMA.extend(
}
)
WARM_TERMINATION_VOLTAGE_DEFAULT = 3.6
def _warm_termination_default(config: ConfigType) -> ConfigType:
"""Keep the default warm termination voltage at or below the termination voltage.
Warn when the default stays below a higher termination voltage.
"""
if (
not isinstance(config, dict)
or CONF_WARM_TERMINATION_VOLTAGE in config
or CONF_TERMINATION_VOLTAGE not in config
):
return config
try:
termination = cv.voltage(config[CONF_TERMINATION_VOLTAGE])
except cv.Invalid:
# The schema reports it
return config
if termination < WARM_TERMINATION_VOLTAGE_DEFAULT - 0.001:
# A warm battery is never charged higher than a cool one
return {
**config,
CONF_WARM_TERMINATION_VOLTAGE: config[CONF_TERMINATION_VOLTAGE],
}
if termination > WARM_TERMINATION_VOLTAGE_DEFAULT + 0.001:
_LOGGER.warning(
"npm1300 '%s' is not set, so a warm battery (45 °C to 60 °C by default) stops "
"charging at %.2fV instead of the %.2fV of '%s'. Set '%s' to the value your "
"battery allows when warm",
CONF_WARM_TERMINATION_VOLTAGE,
WARM_TERMINATION_VOLTAGE_DEFAULT,
termination,
CONF_TERMINATION_VOLTAGE,
CONF_WARM_TERMINATION_VOLTAGE,
)
return config
_CHARGER_SETTINGS_SCHEMA = cv.Schema(
CHARGER_SCHEMA = cv.Schema(
{
# Defaults are the reset values of the product specification
cv.Optional(CONF_CHARGE_CURRENT, default="32mA"): _stepped(
cv.current, 32, 800, 2, "A"
cv.Required(CONF_CHARGE_CURRENT): _stepped(cv.current, 32, 800, 2, "A"),
cv.Optional(CONF_TERMINATION_VOLTAGE, default="4.2V"): _one_of_units(
cv.voltage, TERMINATION_VOLTAGES, "V"
),
cv.Optional(CONF_TERMINATION_VOLTAGE, default="3.6V"): _one_of_units(
cv.Optional(CONF_WARM_TERMINATION_VOLTAGE): _one_of_units(
cv.voltage, TERMINATION_VOLTAGES, "V"
),
cv.Optional(
CONF_WARM_TERMINATION_VOLTAGE,
default=f"{WARM_TERMINATION_VOLTAGE_DEFAULT}V",
): _one_of_units(cv.voltage, TERMINATION_VOLTAGES, "V"),
cv.Optional(CONF_TERMINATION_CURRENT, default="10%"): cv.enum(
TERMINATION_CURRENTS
),
@@ -232,37 +169,22 @@ _CHARGER_SETTINGS_SCHEMA = cv.Schema(
cv.current, list(DISCHARGE_CURRENT_LIMITS), "A"
),
cv.Optional(CONF_RECHARGE, default=True): cv.boolean,
cv.Optional(CONF_ENABLED, default=False): cv.boolean,
cv.Optional(CONF_ENABLED, default=True): cv.boolean,
}
)
CHARGER_SCHEMA = cv.All(_warm_termination_default, _CHARGER_SETTINGS_SCHEMA)
def _check_thermistor(config: ConfigType) -> ConfigType:
"""A wrong thermistor shifts the battery temperature the charger sees, so charging needs one chosen."""
resistance = config.get(CONF_THERMISTOR_RESISTANCE)
if CONF_CHARGER in config and resistance is None:
raise cv.Invalid(
f"'{CONF_THERMISTOR_RESISTANCE}' is required with '{CONF_CHARGER}': set the nominal "
f"resistance of the battery thermistor, or '{THERMISTOR_NONE}'",
path=[CONF_THERMISTOR_RESISTANCE],
)
if CONF_THERMISTOR_BETA in config and resistance in (None, THERMISTOR_NONE):
raise cv.Invalid(
f"'{CONF_THERMISTOR_BETA}' needs '{CONF_THERMISTOR_RESISTANCE}' set to the "
"resistance of the thermistor",
path=[CONF_THERMISTOR_BETA],
)
return config
CONFIG_SCHEMA = cv.All(
CONFIG_SCHEMA = (
cv.Schema(
{
cv.GenerateID(): cv.declare_id(NPM1300Component),
cv.Optional(CONF_VBUS_CURRENT_LIMIT): VBUS_CURRENT_LIMIT,
cv.Optional(CONF_THERMISTOR_RESISTANCE): _thermistor_resistance,
cv.Optional(CONF_THERMISTOR_BETA): cv.int_range(min=1, max=65535),
cv.Optional(CONF_THERMISTOR_RESISTANCE): _one_of_units(
cv.resistance, list(THERMISTOR_RESISTANCES), "kOhm", scale=0.001
),
cv.Optional(CONF_THERMISTOR_BETA, default=3380): cv.int_range(
min=1, max=65535
),
cv.Optional(CONF_CHARGER): CHARGER_SCHEMA,
cv.Optional(CONF_BUCK1): BUCK_SCHEMA,
cv.Optional(CONF_BUCK2): BUCK_SCHEMA,
@@ -271,8 +193,7 @@ CONFIG_SCHEMA = cv.All(
}
)
.extend(cv.polling_component_schema("60s"))
.extend(i2c.i2c_device_schema(0x6B)),
_check_thermistor,
.extend(i2c.i2c_device_schema(0x6B))
)
@@ -287,7 +208,7 @@ def _vbus_current_limit_code(amps: float) -> int:
def _charger_config(config: ConfigType) -> cg.StructInitializer:
termination = _termination_voltage_code(config[CONF_TERMINATION_VOLTAGE])
warm = _termination_voltage_code(config[CONF_WARM_TERMINATION_VOLTAGE])
warm = config.get(CONF_WARM_TERMINATION_VOLTAGE)
return cg.StructInitializer(
NPM1300ChargerConfig,
("current", _millis(config[CONF_CHARGE_CURRENT]) // 2),
@@ -296,7 +217,10 @@ def _charger_config(config: ConfigType) -> cg.StructInitializer:
DISCHARGE_CURRENT_LIMITS[_millis(config[CONF_DISCHARGE_CURRENT_LIMIT])],
),
("termination_voltage", termination),
("warm_termination_voltage", warm),
(
"warm_termination_voltage",
termination if warm is None else _termination_voltage_code(warm),
),
("trickle_voltage", TRICKLE_VOLTAGES[_millis(config[CONF_TRICKLE_VOLTAGE])]),
("termination_current", TERMINATION_CURRENTS[config[CONF_TERMINATION_CURRENT]]),
("recharge", config[CONF_RECHARGE]),
@@ -323,13 +247,6 @@ def _output_config(config: ConfigType | None) -> cg.StructInitializer:
def _config(config: ConfigType) -> cg.StructInitializer:
charger = config.get(CONF_CHARGER)
resistance = config.get(CONF_THERMISTOR_RESISTANCE)
if resistance is None:
thermistor, beta = NPM1300_UNSET, 0
elif resistance == THERMISTOR_NONE:
thermistor, beta = 0, 0
else:
thermistor = THERMISTOR_RESISTANCES[round(resistance / 1000)]
beta = thermistor_beta(config)
return cg.StructInitializer(
NPM1300Config,
(
@@ -337,8 +254,13 @@ def _config(config: ConfigType) -> cg.StructInitializer:
cg.ArrayInitializer(*(_output_config(config.get(key)) for key in OUTPUTS)),
),
("charger", None if charger is None else _charger_config(charger)),
("thermistor_beta", beta),
("thermistor", thermistor),
("thermistor_beta", config[CONF_THERMISTOR_BETA]),
(
"thermistor",
NPM1300_UNSET
if resistance is None
else THERMISTOR_RESISTANCES[round(resistance / 1000)],
),
("charger_configured", charger is not None),
)
+34 -51
View File
@@ -29,7 +29,6 @@ static constexpr uint16_t REG_BCHG_VTERM = 0x030C;
static constexpr uint16_t REG_BCHG_VTERM_R = 0x030D;
static constexpr uint16_t REG_BCHG_VTRICKLE_SEL = 0x030E;
static constexpr uint16_t REG_BCHG_ITERM_SEL = 0x030F;
static constexpr uint16_t REG_BCHG_NTC_STATUS = 0x0332;
static constexpr uint16_t REG_BCHG_CHARGE_STATUS = 0x0334;
static constexpr uint16_t REG_BCHG_ERR_REASON = 0x0336;
static constexpr uint16_t REG_BUCK1_ENA_SET = 0x0400;
@@ -54,9 +53,6 @@ static constexpr uint16_t REG_SHIP_TASK_SHIP_MODE = 0x0B02;
// VBUSINSTATUS
static constexpr uint8_t VBUS_PRESENT = 0x01;
// NTCSTATUS
static constexpr uint8_t NTC_STATUS_COLD = 0x01;
static constexpr uint8_t NTC_STATUS_HOT = 0x08;
// BCHGCHARGESTATUS; bit 0 (battery detected) is reserved since C00 silicon
static constexpr uint8_t CHARGE_STATUS_COMPLETED = 0x02;
static constexpr uint8_t CHARGE_STATUS_TRICKLE = 0x04;
@@ -111,36 +107,26 @@ float ntc_temperature(uint16_t code, float inv_beta) {
#endif
#ifdef USE_TEXT_SENSOR
PROGMEM_STRING_TABLE(ChargerStatusStrings, "Discharging", "Error", "Disabled", "Paused, PMIC Too Hot",
"Charge Complete", "Trickle Charge", "Constant Current", "Constant Voltage",
"Paused, Battery Too Cold", "Paused, Battery Too Hot", "Not Charging");
static constexpr uint8_t CHARGER_STATUS_FIRST_BIT = 3;
// BCHGCHARGESTATUS bits in order of priority, reported from string CHARGER_STATUS_FIRST_BIT on
PROGMEM_STRING_TABLE(ChargerStatusStrings, "Error", "Paused, Die Too Hot", "Charge Complete", "Trickle Charge",
"Constant Current", "Constant Voltage", "Discharging", "Not Charging");
// BCHGCHARGESTATUS bits in order of priority; bit i is reported as string i + 1
static const uint8_t CHARGER_STATUS_BITS[] PROGMEM = {CHARGE_STATUS_DIE_TEMP_HIGH, CHARGE_STATUS_COMPLETED,
CHARGE_STATUS_TRICKLE, CHARGE_STATUS_CONSTANT_CURRENT,
CHARGE_STATUS_CONSTANT_VOLTAGE};
static uint8_t charger_status_index(const NPM1300Status &status) {
if ((status.vbus & VBUS_PRESENT) == 0)
static uint8_t charger_status_index(uint8_t vbus_status, uint8_t charge_status, uint8_t error_reason) {
if (error_reason != 0)
return 0;
if (status.error_reason != 0)
return 1;
if ((status.charger_enable & 1) == 0)
return 2;
for (size_t i = 0; i < sizeof(CHARGER_STATUS_BITS); i++) {
if ((status.charge & progmem_read_byte(&CHARGER_STATUS_BITS[i])) != 0)
return CHARGER_STATUS_FIRST_BIT + i;
if ((charge_status & progmem_read_byte(&CHARGER_STATUS_BITS[i])) != 0)
return i + 1;
}
// The charger stops without an error outside the cold and hot limits of the battery temperature
if ((status.ntc & NTC_STATUS_COLD) != 0)
return 8;
if ((status.ntc & NTC_STATUS_HOT) != 0)
return 9;
return 10;
return (vbus_status & VBUS_PRESENT) == 0 ? 6 : 7;
}
void publish_charger_status(text_sensor::TextSensor *sensor, uint8_t &last, const NPM1300Status &status) {
const uint8_t index = charger_status_index(status);
void publish_charger_status(text_sensor::TextSensor *sensor, uint8_t &last, uint8_t vbus_status, uint8_t charge_status,
uint8_t error_reason) {
const uint8_t index = charger_status_index(vbus_status, charge_status, error_reason);
if (index == last)
return;
last = index;
@@ -212,7 +198,7 @@ bool NPM1300Component::configure_charger_(const NPM1300Config &config) {
split_9bit(charger.discharge_limit, discharge);
uint8_t disable = charger.recharge ? 0 : CHARGER_DISABLE_RECHARGE;
// Without a thermistor the charger reports an NTC error and does not charge
if (config.thermistor == 0 || config.thermistor == NPM1300_UNSET)
if (config.thermistor == NPM1300_UNSET)
disable |= CHARGER_DISABLE_NTC;
const uint8_t enable = (CHARGER_DISABLE_RECHARGE | CHARGER_DISABLE_NTC) & ~disable;
if (this->write_register16(REG_BCHG_ISET_MSB, current, sizeof(current)) != i2c::ERROR_OK ||
@@ -306,40 +292,33 @@ void NPM1300Component::hibernate(uint32_t duration_ms) {
}
void NPM1300Component::update() {
NPM1300Status status;
// NTCSTATUS, DIETEMPSTATUS and BCHGCHARGESTATUS
uint8_t charger_status[3];
if (!this->status_comm_check(this->read_byte_reg16(REG_VBUSIN_STATUS, &status.vbus) &&
this->read_byte_reg16(REG_BCHG_ENABLE_SET, &status.charger_enable) &&
this->read_register16(REG_BCHG_NTC_STATUS, charger_status, sizeof(charger_status)) ==
i2c::ERROR_OK &&
this->read_byte_reg16(REG_BCHG_ERR_REASON, &status.error_reason)))
uint8_t vbus_status;
uint8_t charge_status;
uint8_t error_reason;
if (!this->status_comm_check(this->read_byte_reg16(REG_VBUSIN_STATUS, &vbus_status) &&
this->read_byte_reg16(REG_BCHG_CHARGE_STATUS, &charge_status) &&
this->read_byte_reg16(REG_BCHG_ERR_REASON, &error_reason)))
return;
status.ntc = charger_status[0];
status.charge = charger_status[2];
// Without a thermistor the NTC pin is grounded and can read as a hot battery
if (progmem_read_byte(&this->config_->thermistor) == 0)
status.ntc = 0;
// The chip goes back to its default VBUS current limit whenever VBUS is removed
const bool vbus_present = (status.vbus & VBUS_PRESENT) != 0;
const bool vbus_present = (vbus_status & VBUS_PRESENT) != 0;
if (vbus_present && !this->vbus_present_ && this->vbus_current_limit_ != NPM1300_UNSET &&
!this->status_comm_check(this->apply_vbus_current_limit_()))
return;
this->vbus_present_ = vbus_present;
if (status.error_reason != this->last_error_reason_) {
this->last_error_reason_ = status.error_reason;
if (status.error_reason != 0) {
ESP_LOGW(TAG, "Charger error, BCHGERRREASON 0x%02X", status.error_reason);
if (error_reason != this->last_error_reason_) {
this->last_error_reason_ = error_reason;
if (error_reason != 0) {
ESP_LOGW(TAG, "Charger error, BCHGERRREASON 0x%02X", error_reason);
}
}
#ifdef USE_NPM1300_STATUS_PUBLISHER
if (this->status_publisher_ != nullptr)
this->status_publisher_(status);
this->status_publisher_(vbus_status, charge_status, error_reason);
#endif
#ifdef USE_SWITCH
if (!this->status_comm_check(this->publish_switches_(status)))
if (!this->status_comm_check(this->publish_switches_()))
return;
#endif
@@ -369,10 +348,16 @@ void NPM1300Component::update() {
}
#ifdef USE_SWITCH
bool NPM1300Component::publish_switches_(const NPM1300Status &status) {
PUBLISH_STATE(this->charger_switch_, (status.charger_enable & 1) != 0);
bool NPM1300Component::publish_switches_() {
uint8_t value;
bool ok = true;
if (this->charger_switch_ != nullptr) {
if (this->read_byte_reg16(REG_BCHG_ENABLE_SET, &value)) {
this->charger_switch_->publish_state((value & 1) != 0);
} else {
ok = false;
}
}
switch_::Switch *const bucks[2] = {this->buck1_switch_, this->buck2_switch_};
if (bucks[0] != nullptr || bucks[1] != nullptr) {
if (this->read_byte_reg16(REG_BUCK_STATUS, &value)) {
@@ -476,9 +461,7 @@ void NPM1300Component::dump_config() {
ESP_LOGCONFIG(TAG, " Enabled at boot: %s", YESNO(output.enabled != 0));
}
}
if (config.thermistor == 0) {
ESP_LOGCONFIG(TAG, " Thermistor: none");
} else if (config.thermistor != NPM1300_UNSET) {
if (config.thermistor != NPM1300_UNSET) {
ESP_LOGCONFIG(TAG, " Thermistor B constant: %u", config.thermistor_beta);
}
#ifdef USE_SENSOR
+5 -13
View File
@@ -54,19 +54,10 @@ struct NPM1300Config {
NPM1300OutputConfig outputs[NPM1300_OUTPUT_COUNT];
NPM1300ChargerConfig charger; // only applied when charger_configured
uint16_t thermistor_beta;
uint8_t thermistor; // ADCNTCRSEL code: 0 for none, 1 for 10 kOhm, 2 for 47 kOhm, 3 for 100 kOhm, or NPM1300_UNSET
uint8_t thermistor; // ADCNTCRSEL code: 1 for 10 kOhm, 2 for 47 kOhm, 3 for 100 kOhm, or NPM1300_UNSET
bool charger_configured;
};
/// The status registers read on every update
struct NPM1300Status {
uint8_t vbus; // VBUSINSTATUS
uint8_t charger_enable; // BCHGENABLESET
uint8_t ntc; // NTCSTATUS
uint8_t charge; // BCHGCHARGESTATUS
uint8_t error_reason; // BCHGERRREASON
};
#ifdef USE_NPM1300_DATA_PUBLISHER
/// The 10-bit ADC result whose high 8 bits are adc[msb] and low 2 bits are at `shift` in adc[lsbs]
inline uint16_t adc_code(const uint8_t *adc, uint8_t msb, uint8_t lsbs, uint8_t shift) {
@@ -77,7 +68,8 @@ float ntc_temperature(uint16_t code, float inv_beta);
#endif
#ifdef USE_TEXT_SENSOR
/// Publish the charger status text, only when it differs from `last`
void publish_charger_status(text_sensor::TextSensor *sensor, uint8_t &last, const NPM1300Status &status);
void publish_charger_status(text_sensor::TextSensor *sensor, uint8_t &last, uint8_t vbus_status, uint8_t charge_status,
uint8_t error_reason);
#endif
class NPM1300Component : public PollingComponent, public i2c::I2CDevice {
@@ -103,7 +95,7 @@ class NPM1300Component : public PollingComponent, public i2c::I2CDevice {
float get_setup_priority() const override { return setup_priority::BUS - 1.0f; }
#ifdef USE_NPM1300_STATUS_PUBLISHER
HUB_PUBLISHER(status, const NPM1300Status &)
HUB_PUBLISHER(status, uint8_t, uint8_t, uint8_t)
#endif
#ifdef USE_NPM1300_DATA_PUBLISHER
HUB_PUBLISHER(data, const uint8_t *, float)
@@ -136,7 +128,7 @@ class NPM1300Component : public PollingComponent, public i2c::I2CDevice {
#endif
#ifdef USE_SWITCH
/// Returns false when a status read failed
bool publish_switches_(const NPM1300Status &status);
bool publish_switches_();
#endif
const NPM1300Config *config_;
+5 -6
View File
@@ -21,6 +21,7 @@ from esphome.types import ConfigType
from . import (
ADC,
CONF_NPM1300_ID,
CONF_THERMISTOR_BETA,
CONF_THERMISTOR_RESISTANCE,
CONF_VBUS_CURRENT_LIMIT,
DATA_PUBLISHER,
@@ -29,9 +30,7 @@ from . import (
DUMP_TAG,
IBAT_SCALE,
NPM1300_CHILD_SCHEMA,
THERMISTOR_NONE,
npm1300_ns,
thermistor_beta,
)
DEPENDENCIES = ["npm1300"]
@@ -110,10 +109,10 @@ def _final_validate(config: ConfigType) -> None:
if CONF_BATTERY_TEMPERATURE not in config:
return
hub = fv.get_declaring_config(config[CONF_NPM1300_ID])
if hub.get(CONF_THERMISTOR_RESISTANCE, THERMISTOR_NONE) == THERMISTOR_NONE:
if CONF_THERMISTOR_RESISTANCE not in hub:
raise cv.Invalid(
f"'{CONF_BATTERY_TEMPERATURE}' needs '{CONF_THERMISTOR_RESISTANCE}' set to the "
"nominal resistance of the battery thermistor on the npm1300 component",
f"'{CONF_BATTERY_TEMPERATURE}' needs '{CONF_THERMISTOR_RESISTANCE}' "
"set on the npm1300 component",
path=[CONF_BATTERY_TEMPERATURE],
)
@@ -146,7 +145,7 @@ async def to_code(config: ConfigType) -> None:
if (var := await sensors(CONF_BATTERY_TEMPERATURE, None)) is not None:
hub_config = next(c for c in CORE.config[DOMAIN] if c[CONF_ID] == hub_id)
state = npm1300_ns.ntc_temperature(
_adc(2, 5, 2), 1.0 / thermistor_beta(hub_config)
_adc(2, 5, 2), 1.0 / hub_config[CONF_THERMISTOR_BETA]
)
_add_adc_sensor(hub, var, state, "Battery Temperature")
await sensors(CONF_VBUS_CURRENT_LIMIT, hub.set_vbus_current_limit_sensor)
+3 -11
View File
@@ -15,7 +15,6 @@ from . import (
CONF_THERMISTOR_RESISTANCE,
NPM1300_CHILD_SCHEMA,
OUTPUTS,
THERMISTOR_NONE,
)
DEPENDENCIES = ["npm1300"]
@@ -45,18 +44,11 @@ def _final_validate(config: ConfigType) -> None:
if CONF_CHARGER not in config:
return
hub = fv.get_declaring_config(config[CONF_NPM1300_ID])
# A wrong thermistor shifts the battery temperature the charger sees
if CONF_THERMISTOR_RESISTANCE not in hub:
raise cv.Invalid(
f"The '{CONF_CHARGER}' switch needs '{CONF_THERMISTOR_RESISTANCE}' on the npm1300 "
f"component: the nominal resistance of the battery thermistor, or '{THERMISTOR_NONE}'",
path=[CONF_CHARGER],
)
# Only the charger block turns off the NTC check, without which the charger never starts
if CONF_CHARGER not in hub and hub[CONF_THERMISTOR_RESISTANCE] == THERMISTOR_NONE:
if CONF_CHARGER not in hub and CONF_THERMISTOR_RESISTANCE not in hub:
raise cv.Invalid(
f"The '{CONF_CHARGER}' switch needs a '{CONF_CHARGER}' block when "
f"'{CONF_THERMISTOR_RESISTANCE}' is '{THERMISTOR_NONE}'",
f"The '{CONF_CHARGER}' switch needs a '{CONF_CHARGER}' block or "
f"'{CONF_THERMISTOR_RESISTANCE}' on the npm1300 component",
path=[CONF_CHARGER],
)
+6 -2
View File
@@ -11,12 +11,14 @@ from esphome.cpp_generator import (
from esphome.types import ConfigType
from . import (
CHARGE_STATUS,
CONF_NPM1300_ID,
DUMP,
DUMP_TAG,
ERROR_REASON,
NPM1300_CHILD_SCHEMA,
STATUS,
STATUS_PUBLISHER,
VBUS_STATUS,
npm1300_ns,
)
@@ -46,7 +48,9 @@ async def to_code(config: ConfigType) -> None:
)
STATUS_PUBLISHER.add(
hub,
npm1300_ns.publish_charger_status(parent_ref(var), last, STATUS),
npm1300_ns.publish_charger_status(
parent_ref(var), last, VBUS_STATUS, CHARGE_STATUS, ERROR_REASON
),
)
DUMP.add(
hub,
@@ -2,7 +2,6 @@
#include "esphome/core/hal.h"
#include "esphome/core/helpers.h"
#include "esphome/core/log.h"
#include "esphome/core/progmem.h"
namespace esphome::remote_base {
@@ -223,9 +222,24 @@ optional<IRA211Data> IRA211Protocol::decode(RemoteReceiveData src) {
return out;
}
// Indexed by IRA211Command
PROGMEM_STRING_TABLE(IRA211CommandStrings, "UNKNOWN", "TEMP_UP", "TEMP_DOWN", "UNKNOWN", "MODE", "FAN", "POWER",
"SYNC");
static const LogString *command_to_string(IRA211Command command) {
switch (command) {
case IRA211Command::IRA211_COMMAND_TEMP_UP:
return LOG_STR("TEMP_UP");
case IRA211Command::IRA211_COMMAND_TEMP_DOWN:
return LOG_STR("TEMP_DOWN");
case IRA211Command::IRA211_COMMAND_MODE:
return LOG_STR("MODE");
case IRA211Command::IRA211_COMMAND_FAN:
return LOG_STR("FAN");
case IRA211Command::IRA211_COMMAND_POWER:
return LOG_STR("POWER");
case IRA211Command::IRA211_COMMAND_SYNC:
return LOG_STR("SYNC");
default:
return LOG_STR("UNKNOWN");
}
}
static const LogString *mode_to_string(IRA211Mode mode) {
switch (mode) {
@@ -260,7 +274,7 @@ void IRA211Protocol::dump(const IRA211Data &data) {
const uint8_t fields = layout.has_value() ? layout->fields : 0;
const unsigned whole = data.half_degrees / 2;
const unsigned tenths = (data.half_degrees & 1) ? 5 : 0;
const auto *command = LOG_STR_ARG(IRA211CommandStrings::get_log_str(static_cast<uint8_t>(data.command), 0));
const auto *command = LOG_STR_ARG(command_to_string(data.command));
if (fields == (FIELD_TEMPERATURE | FIELD_MODE | FIELD_FAN)) {
ESP_LOGI(TAG, "Received IRA211: command=%s, temperature=%u.%uC, mode=%s, fan=%s", command, whole, tenths,
LOG_STR_ARG(mode_to_string(data.mode)), LOG_STR_ARG(fan_to_string(data.fan)));
+13 -6
View File
@@ -1,13 +1,22 @@
#include "uln2003.h"
#include "esphome/core/log.h"
#include "esphome/core/progmem.h"
namespace esphome::uln2003 {
ESPHOME_LOG_TAG(TAG, "uln2003.stepper");
// Indexed by ULN2003StepMode
PROGMEM_STRING_TABLE(StepModeStrings, "FULL STEP", "HALF STEP", "WAVE DRIVE", "UNKNOWN");
static const LogString *step_mode_to_log_string(ULN2003StepMode mode) {
switch (mode) {
case ULN2003_STEP_MODE_FULL_STEP:
return LOG_STR("FULL STEP");
case ULN2003_STEP_MODE_HALF_STEP:
return LOG_STR("HALF STEP");
case ULN2003_STEP_MODE_WAVE_DRIVE:
return LOG_STR("WAVE DRIVE");
default:
return LOG_STR("UNKNOWN");
}
}
void ULN2003::setup() {
this->pin_a_->setup();
@@ -45,9 +54,7 @@ void ULN2003::dump_config() {
LOG_PIN(" Pin B: ", this->pin_b_);
LOG_PIN(" Pin C: ", this->pin_c_);
LOG_PIN(" Pin D: ", this->pin_d_);
ESP_LOGCONFIG(
TAG, " Step Mode: %s",
LOG_STR_ARG(StepModeStrings::get_log_str(static_cast<uint8_t>(this->step_mode_), StepModeStrings::LAST_INDEX)));
ESP_LOGCONFIG(TAG, " Step Mode: %s", LOG_STR_ARG(step_mode_to_log_string(this->step_mode_)));
}
void ULN2003::write_step_(int32_t step) {
int32_t n = this->step_mode_ == ULN2003_STEP_MODE_HALF_STEP ? 8 : 4;
@@ -6,7 +6,6 @@
#include "esphome/components/socket/socket.h"
#include "esphome/core/application.h"
#include "esphome/core/log.h"
#include "esphome/core/progmem.h"
#include <cinttypes>
#include <cstdio>
@@ -756,14 +755,38 @@ void VoiceAssistant::client_subscription(api::APIConnection *client, bool subscr
this->client_connected_trigger_.trigger();
}
// Indexed by State
PROGMEM_STRING_TABLE(StateStrings, "IDLE", "START_MICROPHONE", "STARTING_MICROPHONE", "WAIT_FOR_VAD", "WAITING_FOR_VAD",
"START_PIPELINE", "STARTING_PIPELINE", "STREAMING_MICROPHONE", "STOP_MICROPHONE",
"STOPPING_MICROPHONE", "AWAITING_RESPONSE", "STREAMING_RESPONSE", "RESPONSE_FINISHED", "UNKNOWN");
static const LogString *voice_assistant_state_to_string(State state) {
return StateStrings::get_log_str(static_cast<uint8_t>(state), StateStrings::LAST_INDEX);
}
switch (state) {
case State::IDLE:
return LOG_STR("IDLE");
case State::START_MICROPHONE:
return LOG_STR("START_MICROPHONE");
case State::STARTING_MICROPHONE:
return LOG_STR("STARTING_MICROPHONE");
case State::WAIT_FOR_VAD:
return LOG_STR("WAIT_FOR_VAD");
case State::WAITING_FOR_VAD:
return LOG_STR("WAITING_FOR_VAD");
case State::START_PIPELINE:
return LOG_STR("START_PIPELINE");
case State::STARTING_PIPELINE:
return LOG_STR("STARTING_PIPELINE");
case State::STREAMING_MICROPHONE:
return LOG_STR("STREAMING_MICROPHONE");
case State::STOP_MICROPHONE:
return LOG_STR("STOP_MICROPHONE");
case State::STOPPING_MICROPHONE:
return LOG_STR("STOPPING_MICROPHONE");
case State::AWAITING_RESPONSE:
return LOG_STR("AWAITING_RESPONSE");
case State::STREAMING_RESPONSE:
return LOG_STR("STREAMING_RESPONSE");
case State::RESPONSE_FINISHED:
return LOG_STR("RESPONSE_FINISHED");
default:
return LOG_STR("UNKNOWN");
}
};
#ifdef USE_VOICE_ASSISTANT_WAKE_WORD_AUDIO
static bool is_microphone_streaming_state(State state) {
+25 -3
View File
@@ -153,6 +153,7 @@
#define USE_LINE_READER
#define USE_LOCK
#define USE_LOGGER
#define USE_LOGGER_CONSOLE
#define USE_LOGGER_LEVEL_LISTENERS
#define USE_LOGGER_RUNTIME_TAG_LEVELS
#define USE_LVGL
@@ -767,16 +768,26 @@
#if defined(USE_ESP32_VARIANT_ESP32S2)
#define USE_LOGGER_USB_CDC
#define USE_LOGGER_UART_SELECTION_USB_CDC
#define ESPHOME_LOGGER_UART_NAME "USB_CDC"
#define ESPHOME_LOGGER_UART_SELECTION logger::UART_SELECTION_USB_CDC
#elif defined(USE_ESP32_VARIANT_ESP32H21)
#define USE_LOGGER_USB_SERIAL_JTAG
#define USE_LOGGER_UART_SELECTION_USB_SERIAL_JTAG
#define ESPHOME_LOGGER_UART_NAME "USB_SERIAL_JTAG"
#define ESPHOME_LOGGER_UART_SELECTION logger::UART_SELECTION_USB_SERIAL_JTAG
#elif defined(USE_ESP32_VARIANT_ESP32C3) || defined(USE_ESP32_VARIANT_ESP32C5) || \
defined(USE_ESP32_VARIANT_ESP32C6) || defined(USE_ESP32_VARIANT_ESP32C61) || defined(USE_ESP32_VARIANT_ESP32H2) || \
defined(USE_ESP32_VARIANT_ESP32H21) || defined(USE_ESP32_VARIANT_ESP32H4) || defined(USE_ESP32_VARIANT_ESP32P4) || \
defined(USE_ESP32_VARIANT_ESP32S3) || defined(USE_ESP32_VARIANT_ESP32S31)
defined(USE_ESP32_VARIANT_ESP32H4) || defined(USE_ESP32_VARIANT_ESP32P4) || defined(USE_ESP32_VARIANT_ESP32S3) || \
defined(USE_ESP32_VARIANT_ESP32S31)
#define USE_LOGGER_USB_CDC
#define USE_LOGGER_UART_SELECTION_USB_CDC
#define USE_LOGGER_USB_SERIAL_JTAG
#define USE_LOGGER_UART_SELECTION_USB_SERIAL_JTAG
#define ESPHOME_LOGGER_UART_NAME "USB_SERIAL_JTAG"
#define ESPHOME_LOGGER_UART_SELECTION logger::UART_SELECTION_USB_SERIAL_JTAG
#else
#define USE_LOGGER_UART_SELECTION_UART0
#define ESPHOME_LOGGER_UART_NAME "UART0"
#define ESPHOME_LOGGER_UART_SELECTION logger::UART_SELECTION_UART0
#endif
#endif
@@ -790,6 +801,9 @@
#define USE_WIFI_SCAN_RESULTS_LOCK
#define USE_ESP8266_LOGGER_SERIAL
#define USE_ESP8266_LOGGER_SERIAL1
#define USE_LOGGER_UART_SELECTION_UART0
#define ESPHOME_LOGGER_UART_NAME "UART0"
#define ESPHOME_LOGGER_UART_SELECTION logger::UART_SELECTION_UART0
#define USE_ESP8266_PREFERENCES_FLASH
#define ESP8266_PREFERENCES_FLASH_WORDS 128
#define ESP8266_PREFERENCES_RTC_EBOOT_WORDS 32
@@ -835,6 +849,8 @@
#define USE_I2C
#define USE_LOGGER_USB_CDC
#define USE_LOGGER_UART_SELECTION_USB_CDC
#define ESPHOME_LOGGER_UART_NAME "USB_CDC"
#define ESPHOME_LOGGER_UART_SELECTION logger::UART_SELECTION_USB_CDC
#define USE_SOCKET_IMPL_LWIP_TCP
#define USE_RP2040_BLE
#define USE_RP2_BLE_TRACKER
@@ -865,6 +881,9 @@
#if defined(USE_BK72XX) || defined(USE_RTL87XX) || defined(USE_LN882X)
#define USE_LIBRETINY_CRASH_HANDLER
#endif
#define USE_LOGGER_UART_SELECTION_DEFAULT
#define ESPHOME_LOGGER_UART_NAME "DEFAULT"
#define ESPHOME_LOGGER_UART_SELECTION logger::UART_SELECTION_DEFAULT
#ifdef USE_BK72XX
#define USE_REMOTE_RECEIVER_TIMER_SAMPLING
#endif
@@ -919,8 +938,11 @@
#define ESPHOME_TASK_LOG_BUFFER_SIZE 768
#define USE_LOGGER_EARLY_MESSAGE
#define USE_LOGGER_UART_SELECTION_USB_CDC
#define ESPHOME_LOGGER_UART_NAME "USB_CDC"
#define ESPHOME_LOGGER_UART_SELECTION logger::UART_SELECTION_USB_CDC
#define USE_LOGGER_USB_CDC
#define USE_LOGGER_WAIT_FOR_CDC
#define USE_LOGGER_ZEPHYR_CDC_LOOP
#define USE_NRF52_DFU
#define USE_NRF52_REG0_VOUT 5
#define USE_NRF52_UICR_ERASE
+1 -3
View File
@@ -846,9 +846,7 @@ def convert_visual_temperatures(
that needs ``full_config`` is left for final validation, which runs this again with it."""
if (unit := entity_temperature_unit(config, full_config)) is None:
return config
# A platform entry that only holds nested entities has no visual section of its own
if (visual := config.get(CONF_VISUAL)) is None:
return config
visual = config[CONF_VISUAL]
convert_temperature_keys(visual, (CONF_MIN_TEMPERATURE, CONF_MAX_TEMPERATURE), unit)
section = visual if delta_section is None else visual.get(delta_section)
if section is not None:
@@ -222,20 +222,6 @@ def test_a_resolved_unit_waits_for_the_full_config() -> None:
assert config[CONF_VISUAL][CONF_MIN_TEMPERATURE] == pytest.approx(59.0)
def test_final_validate_skips_a_platform_that_only_holds_nested_climates() -> None:
"""A hub platform may put each of its climates under a key of one platform entry."""
nested = climate_schema(climate_ns.class_("NestedClimate", Climate))
platform_schema = cv.Schema({cv.Optional("zone_1"): nested})
config = platform_schema(
{"zone_1": {CONF_NAME: "Zone 1", CONF_VISUAL: {CONF_MIN_TEMPERATURE: "50°F"}}}
)
# The platform entry itself is not a climate and has no visual section
assert CONF_VISUAL not in config
_final_validate([config])
# The nested climate was converted by its own schema
assert config["zone_1"][CONF_VISUAL][CONF_MIN_TEMPERATURE] == pytest.approx(10.0)
@pytest.mark.parametrize(
("use_fahrenheit", "cn105_lines"),
[
+53 -44
View File
@@ -68,38 +68,6 @@ def test_logger_pre_setup_before_other_components(generate_main):
)
def test_default_uart_selection_is_not_emitted(generate_main):
"""UART0 is the C++ initializer on ESP8266, so the setter is skipped."""
main_cpp = generate_main("tests/component_tests/logger/test_logger.yaml")
assert "set_uart_selection(" not in main_cpp
def test_custom_uart_selection_is_emitted(generate_main):
"""A non default UART still reaches the setter before pre_setup()."""
main_cpp = generate_main("tests/component_tests/logger/test_logger_uart1.yaml")
assert "set_uart_selection(logger::UART_SELECTION_UART1);" in main_cpp
def test_libretiny_default_uart_selection_is_not_emitted(generate_main):
"""DEFAULT is the C++ initializer on LibreTiny, so the setter is skipped."""
main_cpp = generate_main(
"tests/component_tests/logger/test_logger_libretiny_default.yaml"
)
assert "set_uart_selection(" not in main_cpp
def test_libretiny_uart0_is_emitted(generate_main):
"""UART0 is not the LibreTiny initializer, so it must still be set."""
main_cpp = generate_main(
"tests/component_tests/logger/test_logger_libretiny_uart0.yaml"
)
assert "set_uart_selection(logger::UART_SELECTION_UART0);" in main_cpp
def test_ram_log_strings_is_deprecated(
generate_main: Callable[[str | Path], str],
caplog: pytest.LogCaptureFixture,
@@ -168,35 +136,76 @@ def test_log_v2_only_on_native_toolchain(
@pytest.mark.parametrize(
("config", "expected"),
("config", "port", "zephyr_cdc_loop"),
[
pytest.param("test_logger_rp2_usb_cdc.yaml", {"USB_CDC"}, id="rp2_usb_cdc"),
pytest.param("test_logger_rp2_uart0.yaml", set(), id="rp2_uart0"),
pytest.param("test_logger_esp32_usb_cdc.yaml", {"USB_CDC"}, id="esp32_usb_cdc"),
pytest.param("test_logger.yaml", "UART0", False, id="esp8266_default"),
pytest.param("test_logger_uart1.yaml", "UART1", False, id="esp8266_uart1"),
pytest.param(
"test_logger_uart0_swap.yaml", "UART0_SWAP", False, id="esp8266_uart0_swap"
),
pytest.param(
"test_logger_libretiny_default.yaml",
"DEFAULT",
False,
id="libretiny_default",
),
pytest.param(
"test_logger_libretiny_uart0.yaml", "UART0", False, id="libretiny_uart0"
),
pytest.param(
"test_logger_rp2_usb_cdc.yaml", "USB_CDC", False, id="rp2_usb_cdc"
),
pytest.param("test_logger_rp2_uart0.yaml", "UART0", False, id="rp2_uart0"),
pytest.param(
"test_logger_esp32_usb_cdc.yaml", "USB_CDC", False, id="esp32_usb_cdc"
),
pytest.param(
"test_logger_esp32_usb_serial_jtag.yaml",
{"USB_SERIAL_JTAG"},
"USB_SERIAL_JTAG",
False,
id="esp32_usb_serial_jtag",
),
pytest.param("test_logger_nrf52_usb_cdc.yaml", {"USB_CDC"}, id="nrf52_usb_cdc"),
pytest.param(
"test_logger_nrf52_usb_cdc.yaml", "USB_CDC", True, id="nrf52_usb_cdc"
),
# Zephyr polls the USB port only when it logs there
pytest.param(
"test_logger_nrf52_usb_cdc_no_serial.yaml", set(), id="nrf52_no_serial"
"test_logger_nrf52_usb_cdc_no_serial.yaml",
"USB_CDC",
False,
id="nrf52_no_serial",
),
],
)
def test_uart_selection_defines(
generate_main: Callable[[str | Path], str],
config: str,
expected: set[str],
port: str,
zephyr_cdc_loop: bool,
) -> None:
"""USB ports get a selection define, which gates their port code and crash replay."""
"""The chosen port is fixed at build time: one flag, its enum value and its dump_config name."""
generate_main(f"tests/component_tests/logger/{config}")
defines = {d.name: d.value for d in CORE.defines}
prefix = "USE_LOGGER_UART_SELECTION_"
assert {
d.name.removeprefix(prefix) for d in CORE.defines if d.name.startswith(prefix)
} == expected
assert {d.removeprefix(prefix) for d in defines if d.startswith(prefix)} == {port}
assert (
str(defines["ESPHOME_LOGGER_UART_SELECTION"])
== f"logger::UART_SELECTION_{port}"
)
assert str(defines["ESPHOME_LOGGER_UART_NAME"]) == f'"{port}"'
assert ("USE_LOGGER_ZEPHYR_CDC_LOOP" in defines) is zephyr_cdc_loop
def test_esp8266_without_serial_dumps_no_port(
generate_main: Callable[[str | Path], str],
) -> None:
"""ESP8266 without serial logging keeps UART0 selected but never opens it."""
generate_main("tests/component_tests/logger/test_logger_no_serial.yaml")
defines = {d.name: d.value for d in CORE.defines}
assert "USE_LOGGER_UART_SELECTION_UART0" in defines
assert str(defines["ESPHOME_LOGGER_UART_NAME"]) == '"NONE"'
def test_log_listener_slots_count_every_listener(
@@ -0,0 +1,9 @@
---
esphome:
name: test
esp8266:
board: d1_mini_lite
logger:
baud_rate: 0
@@ -0,0 +1,9 @@
---
esphome:
name: test
esp8266:
board: d1_mini_lite
logger:
hardware_uart: UART0_SWAP
+2 -95
View File
@@ -8,16 +8,11 @@ from esphome.components.npm1300 import (
CHARGER_SCHEMA,
NPM1300_UNSET,
OUTPUT_VOLTAGE,
THERMISTOR_NONE,
VBUS_CURRENT_LIMIT,
_charger_config,
_check_thermistor,
_config,
_output_config,
_termination_voltage_code,
_thermistor_resistance,
_vbus_current_limit_code,
thermistor_beta,
)
from esphome.const import CONF_MODE, CONF_VOLTAGE
from esphome.cpp_generator import StructInitializer
@@ -59,35 +54,10 @@ def test_termination_voltage_gap_rejected(voltage: str) -> None:
CHARGER_SCHEMA({"charge_current": "100mA", "termination_voltage": voltage})
def test_warm_termination_defaults_to_reset_value() -> None:
def test_warm_termination_defaults_to_termination() -> None:
fields = _charger({"charge_current": "100mA", "termination_voltage": "4.1V"})
assert fields["termination_voltage"] == "6"
assert fields["warm_termination_voltage"] == "2"
@pytest.mark.parametrize(
("config", "warns"),
[
({"termination_voltage": "4.2V"}, True),
({"termination_voltage": "3.5V"}, False),
({"termination_voltage": "3.6V"}, False),
({}, False),
({"termination_voltage": "4.2V", "warm_termination_voltage": "4.0V"}, False),
],
)
def test_warm_termination_default_warning(
config: ConfigType, warns: bool, caplog: pytest.LogCaptureFixture
) -> None:
CHARGER_SCHEMA(config)
assert ("warm_termination_voltage" in caplog.text) is warns
@pytest.mark.parametrize(("termination", "code"), [("3.5V", "0"), ("3.55V", "1")])
def test_warm_termination_default_not_above_termination(
termination: str, code: str
) -> None:
fields = _charger({"termination_voltage": termination})
assert fields["warm_termination_voltage"] == code
assert fields["warm_termination_voltage"] == "6"
def test_warm_termination_code() -> None:
@@ -142,66 +112,3 @@ def test_vbus_current_limit_code(limit: str, code: int) -> None:
def test_vbus_current_limit_rejected(limit: str) -> None:
with pytest.raises(cv.Invalid):
VBUS_CURRENT_LIMIT(limit)
def test_charger_needs_thermistor() -> None:
with pytest.raises(cv.Invalid, match="thermistor_resistance"):
_check_thermistor({"charger": {}})
config = {"charger": {}, "thermistor_resistance": THERMISTOR_NONE}
assert _check_thermistor(config) is config
@pytest.mark.parametrize("resistance", [None, THERMISTOR_NONE])
def test_thermistor_beta_needs_resistance(resistance: str | None) -> None:
config = {"thermistor_beta": 3380}
if resistance is not None:
config["thermistor_resistance"] = resistance
with pytest.raises(cv.Invalid, match="thermistor_beta"):
_check_thermistor(config)
@pytest.mark.parametrize(
("resistance", "beta"), [(10000.0, 3380), (47000.0, 4050), (100000.0, 4250)]
)
def test_thermistor_beta_default(resistance: float, beta: int) -> None:
assert thermistor_beta({"thermistor_resistance": resistance}) == beta
def test_thermistor_beta_configured() -> None:
config = {"thermistor_resistance": 47000.0, "thermistor_beta": 3950}
assert thermistor_beta(config) == 3950
@pytest.mark.parametrize(
("resistance", "code", "beta"),
[
(None, str(NPM1300_UNSET), "0"),
(THERMISTOR_NONE, "0", "0"),
(100000.0, "3", "4250"),
],
)
def test_config_thermistor(
resistance: str | float | None, code: str, beta: str
) -> None:
config = {} if resistance is None else {"thermistor_resistance": resistance}
fields = _fields(_config(config))
assert fields["thermistor"] == code
assert fields["thermistor_beta"] == beta
@pytest.mark.parametrize(
("value", "result"),
[
("10kOhm", 10000.0),
("0.047MOhm", 47000.0),
("100000", 100000.0),
("None", "none"),
],
)
def test_thermistor_resistance(value: str, result: float | str) -> None:
assert _thermistor_resistance(value) == result
def test_thermistor_resistance_rejected() -> None:
with pytest.raises(cv.Invalid, match="10kOhm, 47kOhm, 100kOhm or none"):
_thermistor_resistance("22kOhm")
-6
View File
@@ -1,6 +0,0 @@
from tests.testing_helpers import ComponentManifestOverride
def override_manifest(manifest: ComponentManifestOverride) -> None:
# touchscreen.h includes display.h
manifest.dependencies = manifest.dependencies + ["display"]
-42
View File
@@ -1,42 +0,0 @@
#pragma once
#include <array>
#include <gtest/gtest.h>
#include "esphome/components/cst816/touchscreen/cst816_touchscreen.h"
namespace esphome::cst816::testing {
static constexpr uint8_t ADDRESS = 0x15;
// The driver reads REG_STATUS onwards in one transfer: status, gesture, touch count, then two points.
static constexpr size_t FRAME_SIZE = 13;
/// Serves one fixed status frame.
class FrameBus final : public i2c::I2CBus {
public:
explicit FrameBus(std::array<uint8_t, FRAME_SIZE> frame) : frame_(frame) {}
i2c::ErrorCode write_readv(uint8_t address, const uint8_t *write_buffer, size_t write_count, uint8_t *read_buffer,
size_t read_count) override {
EXPECT_EQ(address, ADDRESS);
for (size_t i = 0; i < read_count; i++)
read_buffer[i] = i < FRAME_SIZE ? this->frame_[i] : 0;
return i2c::ERROR_OK;
}
protected:
std::array<uint8_t, FRAME_SIZE> frame_;
};
inline std::array<uint8_t, FRAME_SIZE> make_frame(uint8_t touch_num, uint16_t x = 0, uint16_t y = 0) {
std::array<uint8_t, FRAME_SIZE> frame{};
frame[REG_TOUCH_NUM] = touch_num;
frame[REG_XPOS_HIGH] = (x >> 8) & 0x0F;
frame[REG_XPOS_LOW] = x & 0xFF;
frame[REG_YPOS_HIGH] = (y >> 8) & 0x0F;
frame[REG_YPOS_LOW] = y & 0xFF;
return frame;
}
} // namespace esphome::cst816::testing
@@ -1,88 +0,0 @@
#include <gtest/gtest.h>
#include <memory>
#include "../common.h"
namespace esphome::cst816::testing {
class CST816TouchscreenTest : public ::testing::Test {
protected:
void feed_(const std::array<uint8_t, FRAME_SIZE> &frame) {
this->bus_ = std::make_unique<FrameBus>(frame);
this->touchscreen_.set_i2c_bus(this->bus_.get());
this->touchscreen_.set_i2c_address(ADDRESS);
this->touchscreen_.update_touches();
}
std::unique_ptr<FrameBus> bus_;
CST816Touchscreen touchscreen_;
};
// An idle frame reports 0xFF in the touch count byte and 0xFFF coordinates. Masking 0xFF to the
// low two bits turns that into three touches at the maximum position, a phantom tap.
TEST_F(CST816TouchscreenTest, IdleAllOnesFrameIsIgnored) {
this->feed_(make_frame(0xFF, 0x0FFF, 0x0FFF));
EXPECT_TRUE(this->touchscreen_.get_touches().empty());
}
TEST_F(CST816TouchscreenTest, ZeroTouchCountIsIgnored) {
this->feed_(make_frame(0));
EXPECT_TRUE(this->touchscreen_.get_touches().empty());
}
// Three is the boundary the guard rejects: the old mask turned a count of three into three
// touches, so this is the value whose behaviour changes.
TEST_F(CST816TouchscreenTest, TouchCountThreeIsIgnored) {
this->feed_(make_frame(3, 100, 200));
EXPECT_TRUE(this->touchscreen_.get_touches().empty());
}
// The count is the whole low nibble, so 0x05 must not be masked down to one touch by a 0x03 mask.
TEST_F(CST816TouchscreenTest, TouchCountFiveIsIgnored) {
this->feed_(make_frame(0x05, 100, 200));
EXPECT_TRUE(this->touchscreen_.get_touches().empty());
}
TEST_F(CST816TouchscreenTest, SingleTouchIsReported) {
this->feed_(make_frame(1, 300, 100));
auto touches = this->touchscreen_.get_touches();
ASSERT_EQ(touches.size(), 1u);
EXPECT_EQ(touches[0].x_raw, 300);
EXPECT_EQ(touches[0].y_raw, 100);
}
// CST826/CST836 can report two points; the driver only consumes the first one.
TEST_F(CST816TouchscreenTest, TwoPointFrameReportsFirstPoint) {
this->feed_(make_frame(2, 300, 100));
auto touches = this->touchscreen_.get_touches();
ASSERT_EQ(touches.size(), 1u);
EXPECT_EQ(touches[0].x_raw, 300);
EXPECT_EQ(touches[0].y_raw, 100);
}
TEST_F(CST816TouchscreenTest, SentinelPositionIsIgnored) {
this->feed_(make_frame(1, 0x0FFF, 100));
EXPECT_TRUE(this->touchscreen_.get_touches().empty());
}
// The sentinel is checked on both axes; a valid X with Y=0xFFF is still an idle reading.
TEST_F(CST816TouchscreenTest, SentinelYPositionIsIgnored) {
this->feed_(make_frame(1, 100, 0x0FFF));
EXPECT_TRUE(this->touchscreen_.get_touches().empty());
}
// x_raw_max_/y_raw_max_ are calibration endpoints, not validity limits: the base class applies them
// after swapping axes and clamps readings outside them. A touch beyond the calibrated maximum is
// still a real touch and must reach the base class.
TEST_F(CST816TouchscreenTest, CalibrationBoundsDoNotDropTouches) {
this->touchscreen_.set_calibration(0, 240, 0, 320);
this->touchscreen_.set_swap_xy(true);
this->feed_(make_frame(1, 300, 100));
auto touches = this->touchscreen_.get_touches();
ASSERT_EQ(touches.size(), 1u);
EXPECT_EQ(touches[0].x_raw, 100);
EXPECT_EQ(touches[0].y_raw, 300);
}
} // namespace esphome::cst816::testing
+22 -38
View File
@@ -1,38 +1,29 @@
npm1300:
- id: pmic
i2c_id: i2c_bus
vbus_current_limit: 500mA
thermistor_resistance: 10kOhm
thermistor_beta: 3380
charger:
charge_current: 150mA
termination_voltage: 4.2V
warm_termination_voltage: 4.0V
termination_current: 20%
trickle_voltage: 2.5V
discharge_current_limit: 1000mA
recharge: true
buck2:
voltage: 3.3V
ldo1:
voltage: 3.3V
mode: ldo
enabled: true
ldo2:
mode: load_switch
enabled: false
# A battery without a thermistor
- id: pmic_no_ntc
i2c_id: i2c_bus
address: 0x6C
thermistor_resistance: none
charger:
termination_voltage: 3.5V
enabled: true
id: pmic
i2c_id: i2c_bus
vbus_current_limit: 500mA
thermistor_resistance: 10kOhm
thermistor_beta: 3380
charger:
charge_current: 150mA
termination_voltage: 4.2V
warm_termination_voltage: 4.0V
termination_current: 20%
trickle_voltage: 2.5V
discharge_current_limit: 1000mA
recharge: true
buck2:
voltage: 3.3V
ldo1:
voltage: 3.3V
mode: ldo
enabled: true
ldo2:
mode: load_switch
enabled: false
sensor:
- platform: npm1300
npm1300_id: pmic
battery_voltage:
name: Battery Voltage
battery_current:
@@ -50,7 +41,6 @@ sensor:
binary_sensor:
- platform: npm1300
npm1300_id: pmic
vbus_present:
name: VBUS Present
vbus_current_limit_active:
@@ -64,13 +54,11 @@ binary_sensor:
text_sensor:
- platform: npm1300
npm1300_id: pmic
charger_status:
name: Charger Status
switch:
- platform: npm1300
npm1300_id: pmic
charger:
name: Charger
buck1:
@@ -79,10 +67,6 @@ switch:
name: LDO1
ldo2:
name: LDO2
- platform: npm1300
npm1300_id: pmic_no_ntc
charger:
name: Charger Without Thermistor
button:
- platform: template
-1
View File
@@ -17,7 +17,6 @@ void setup() {
App.pre_setup(name, sizeof(name) - 1, friendly_name, sizeof(friendly_name) - 1);
auto *log = new logger::Logger(115200); // NOLINT
log->pre_setup();
log->set_uart_selection(logger::UART_SELECTION_UART0);
App.register_component_(log);
auto *wifi = new wifi::WiFiComponent(); // NOLINT
@@ -1550,15 +1550,6 @@ def test_convert_visual_temperatures(
convert_visual_temperatures({"visual": {}}, delta_keys, delta_section)
def test_convert_visual_temperatures_without_a_visual_section() -> None:
"""A platform entry that only holds nested entities has no visual section and is left alone."""
nested = {"visual": {"min_temperature": (50.0, "°F")}}
config = {"zone_1": nested}
assert convert_visual_temperatures(config, ("step",)) is config
assert nested["visual"]["min_temperature"] == (50.0, "°F")
@pytest.mark.asyncio
async def test_setup_entity_integrations_registers_mqtt_and_web_server(
monkeypatch: pytest.MonkeyPatch, setup_test_environment: list[str]
+1 -7
View File
@@ -1792,13 +1792,7 @@ def test_ccache_env_opt_in_without_binary(
# Explicit IDF_CCACHE_ENABLE=1 forces it on; without a usable binary
# IDF's CMake silently skips ccache, so this branch must say so out loud.
p1, p2, p3 = _ccache_patches(tmp_path, None, tmp_path / "build")
with (
patch.dict("os.environ", {"IDF_CCACHE_ENABLE": "1"}, clear=True),
patch("esphome.espidf.framework.shutil.which", return_value=None),
p1,
p2,
p3,
):
with patch.dict("os.environ", {"IDF_CCACHE_ENABLE": "1"}, clear=True), p1, p2, p3:
env = _ccache_env()
assert env["IDF_CCACHE_ENABLE"] == "1"
assert env["CCACHE_DIR"] == str(tmp_path / "tools" / "ccache")